Dini Argeo 3590 EBOX Series Technical Manual Download Page 81

Page: 81 / 132

3590EKR, 3590EXP, 3590EXT, 3590 EBOX, CPWE, CPWET series indicator E-AF03_05.01_14.07_EN_T.doc

5.8.1 SERIAL COMMANDS FOR MANAGING THE ALIBI MEMORY:

!! IMPORTANT !!

If the serial commands are transmitted in the format:
<ESC> command <STX>

in which:

<ESC>

is the ASCII decimal 27 character

<STX>

is the ASCII decimal 02 character

Also the relative answer will be:

<ESC> string <STX>

REQUEST WEIGHT VALUE WITH WEIGH ID

The command which allows saving the weight in the alibi memory and the transmission is:

<II>PID<CRLF>

< II >

= machine code, only if functioning in 485

PID

= saving command of the weight data in the alibi memory

= ASCII 13 decimal code

= ASCII 10 decimal code

If the gross weight is equal or greater than zero and stable, the instrument will save the weight on the belt in the alibi

memory.
And the PID string (weight/id) will be transmitted on the PC port; this is described in the following section.

STRING FORMAT (WEIGHT/ID)

The PID string contains all the information regarding the executed weigh.

DESCRIPTION OF THE PID STRING:
<ESC>[II]

PID

SS,B,LLLLLLLLLLUU,YYTTTTTTTTTTUU,(ID | NO) <CR or CRLF>

in which:

[II]

485 address (only in the case of 485 transmission mode)

US instable weight

ST stable weight

OL weight out of range (greater)

UL weight out of range (lower)

comma character, ASCII 044

number of selected channel

comma character, ASCII 044

LLLLLLLLLL

gross weight on 10 digits

unit of measure

comma character, ASCII 044

2 spaces in the case of null tare or semiautomatic tare, PT in the case of preset tare

TTTTTTTTTT tare weight on 10 digits
,

comma character, ASCII 044

XXXXX-YYYYYY or “NO”: weigh not stored in the alibi memory; the gross weight is

negative or unstable.

<CR o CRLF> Terminator, ASCII 13 and ASCII 10 characters

WEIGH READING

Command:

[II]ALRDXXXXX-YYYYYY <CR o CRLF>

in which

[II]

485 address (only in the case of 485 transmission mode)

XXXXX

rewriting number, from 0 up to 255.

ASCII 045 character

YYYYYY

ID code

<CR o CRLF> terminator, ASCII 13 and ASCII 10 characters

Summary of Contents for 3590 EBOX Series





































































































































Search results

Summary of Contents for 3590 EBOX Series

Reviews:

Brands by name

Popular brands

Dini Argeo 3590 EBOX Series, Technical Manual

Search results

Summary of Contents for 3590 EBOX Series

Reviews:

Brands by name

Popular brands