manualshive.com logo in svg

Dini Argeo 3590 EBOX Series, Technical Manual

Share
Download
Dini Argeo 3590 EBOX Series Technical Manual Download Page 29

3590EKR, 3590EXP, 3590EXT, 3590 EBOX, CPWE, CPWET series indicator   E-AF03_05.01_14.07_EN_T.doc 

 

 

29 

<< totAL >>  

TOTALIZER

 

<< WEi.Mod

 

>>

  SELECTION OF WEIGHING MODE 

One selects the type of weighing which one wants to carry out: 

 

nor.WGt 

NORMAL WEIGHING (simple input/output)

 

With two scales, by confirming with ENTER one is asked whether to enable the “A+B” mode: 
DISABLED 
ENABLED

 

 

 

SEC.WGt 

SECOND WEIGH (input/output with trailer weighing)

 

(!) nor.WGt 

 

<< WEi.MEM

 

>>

  TYPE OF INPUT WEIGH MEMORISATION 

-

 

WEi.Cod 

ID CODE

 

-

 

PLAtE   

LICENSE PLATE

 

(!) WEi.Cod 

 

<< Pro.LSt

 

>>

  LIST OF PROGRESSIVE WEIGHS (only for weighing through ID CODE)

 

If this parameter is DISABLED, each input weigh is linked to the lowest ID code available; if it is ENABLED, the ID 
code following the last input weigh is linked to it. 

(!)DISABLED 

 

<< t.ModE >>  

TYPE OF TOTALISATION 

It is possible to select the type of totalisation: 
- 

MAnuAL

 

manual totaliser (reenabling according to how the 

rEACt 

“REENABLINGS”

 

step is set.

 

- 

ALWAYS

 

totaliser always (always active). 

(!) MAnuAL 

 

<< rESEt

 

>>

  CONFIRM RESET 

It is possible to select the automatic resetting of the totals when these are printed (

Disable

) or the resetting upon 

request (

Enable

). 

(!) EnAbLE 

 

<< i.o.SCA >>  

SETS INPUT/OUTPUT SCALES 

With the possibility of connecting a second scale, one sets how the two scales will be used: 

SEt.i.o1 

BIL1=IN BIL2=OUT: one sets the first scale (in other words, the one connected to the terminal board or to 
channel 1) as INPUT, and the second one (in other words the one connected to channel 2) as OUTPUT. 

SEt.i.o2 

BIL1=IN BIL1=OUT: one sets the first scale as INPUT as well as OUTPUT. 

FrEE 

FREE: one can freely use the two scales as: INPUT in the first / OUTPUT in the second and vice versa, or 
INPUT/OUTPUT in the first or INPUT/OUTPUT in the second.

 

(!) FrEE 

 

<< C.EntEr >>  

CONFIGURED ENTER KEY

 

In the “second weigh” functioning mode (trailer weigh), it is possible to configure the 

ENTER

 key for acquiring the 

weight of the trailer: 

ConFEr 

CONFIRM SCALE: by pressing the 

ENTER

 key one confirms the second weigh on the current scale. 

inVErt 

INVERT SCALE: By pressing the 

ENTER

 key one confirms automatically switching to the other scale. 

(!) ConFEr

 

 

<< Add.tAr

 

>>

  ADDITIONAL TARE

 

In  this  step  one  can  enable  (

ENABLED

)  or  disable  (

DISABLED

)  the  request  to  enter  an  additional  tare,  at  the 

moment of the output weigh execution. (

USER MAN.REF.

). 

(!) DISABLED 

 

Summary of Contents for 3590 EBOX Series





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands