manualshive.com logo in svg

Dini Argeo 3590 EBOX Series, Technical Manual

Share
Download
Dini Argeo 3590 EBOX Series Technical Manual Download Page 68

3590EKR, 3590EXP, 3590EXT, 3590 EBOX, CPWE, CPWET series indicator   E-AF03_05.01_14.07_EN_T.doc 

 

 

68 

TRANSMISSION ON STABILITY 

[available in ComPC] 

Transmission  is  automatic  each  time  the  weight  put  on  the  platform  reaches  stability  ("~"  pilot  light  off);  the  minimum 
transmission limit is of 10 divisions with a NON APPROVED instrument and 20 divisions with an APPROVED instrument. 
The reactivation of the transmission takes place depending on how the 

F.modE >> rEACt 

“REACTIVATIONS” parameter of 

the SET-UP environment has been set (passage by zero of the net weight or weight instability). 
 
RS485 TRANSMISSION 

[available in ComPC] 

On Com3 is available a RS485 Half Duplex serial output, enabling the possibility of bi-directional communication up to 63 
indicators to just one computer. 
The transmission protocol is the same as that of transmission upon request, with the adding of a code that identifies the 
weight indicator (i.e. “00READ <CR LF>”) 

 
TRANSMISSION AT THE END OF THE WEIGHING CYCLE 

[available in ComPC]  

The transmission takes place automatically each time that an input/output weighing cycle or a single weigh is carried out; 

the transmitted string corresponds to the one of the “LAST” command (see following paragraph). 
 

5.6 SERIAL COMMANDS FORMAT 

 

 

 

 

SERIAL ERRORS 

 
Upon each serial command received the instrument transmits a string containing the answer (see the command description) 

or it transmits one of the following indications: 

OK<CR LF> 

it is shown when a correct command is transmitted from the PC to the indicator. The OK answer does 
not imply that the instrument executes the zero. 

ERR01<CR LF>

  it is shown when a correct command is transmitted from the PC to the indicator however it is followed 

by letters inserted involuntarily (I.E.: READF, TARES…). 

ERR02<CR LF>

  it is shown when a correct command is transmitted from the PC to the indicator, but containing wrong 

data. 

ERR03<CR LF>

  it is shown when a non allowed command is transmitted. It may be a command not used in the selected 

functioning mode or the command reaches the indicator in the instant in which the keyboard buffer is 

already occupied by another command 

ERR04<CR LF>

  it is shown when an inexistent command is transmitted. 

NOTE

: The instrument doesn’t transmit any indication with the short commands, like the ones made up of only one letter 

and then the possible parameter. 

 

 

LEGEND

  

[CC] o <II>

 

instrument code, e.g. 00 (only with RS485 protocol) 

<CR LF>

 

Carriage  Line Feed (ASCII characters 13 and 10) 

<ESC>

 

ASCII character ASCII 27 

<STX>

 

ASCII character ASCII 02 

b 

space character, ASCII 32. 

Summary of Contents for 3590 EBOX Series





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands