manualshive.com logo in svg

Digital Equipment Alpha 21164PC, Hardware Reference Manual

The Digital Equipment Alpha 21164PC is a cutting-edge computing solution that promises unparalleled performance. For in-depth knowledge and optimal usage, it is essential to have access to the comprehensive Hardware Reference Manual. You can now conveniently download this manual for free from manualshive.com, empowering you with complete control over your device.

Share
Download
background image

7–6

Initialization and Configuration

29 September 1997 – Subject To Change

sysclk Ratio and Delay

7.2 sysclk Ratio and Delay

While in reset, the 21164PC reads sysclk configuration parameters from the interrupt 
signal pins. These inputs should be driven with the correct configuration values 
whenever sys_reset_l is asserted. Refer to Section 4.2.2 and Section 4.2.3 for rele-
vant input signals and ratio/delay values.

If the signal inputs reflecting configuration parameters change while sys_reset_l is 
asserted, allow 20 internal CPU cycles before the new sysclk behavior is correct.

7.3 Built-In Self-Test (BiSt)

Upon deassertion of signal sys_reset_l, the 21164PC automatically executes the 
Icache built-in self-test (BiSt). The Icache is automatically tested and the result is 
made available in the ICSR IPR and on signal test_status_h<1>. Internally, the CPU 
reset continues to be asserted throughout the BiSt process. For additional informa-
tion, refer to Section 9.4.4.1.

7.4 Serial Read-Only Memory Interface Port

The serial read-only memory (SROM) interface provides the initialization data load 
path from a system SROM to the instruction cache (Icache). Following initialization, 
this interface can function as a diagnostic port using privileged architecture library 
code (PALcode).

The following signals make up the SROM interface:

srom_present_l
srom_data_h
srom_oe_l
srom_clk_h

During system reset, the 21164PC samples the srom_present_l signal for the pres-
ence of SROM. If srom_present_l is deasserted, the SROM load is disabled and the 
reset sequence clears the Icache valid bits. This causes the first instruction fetch to 
miss the Icache and read instructions from offchip memory.

Summary of Contents for Alpha 21164PC





















































































































































































































































































































































































Reviews:

No comments

Related manuals for Alpha 21164PC

Cabletron Systems MMAC-5FNB Overview And Setup Manual preview
MMAC-5FNB
Brand: Cabletron Systems Pages: 21
Paradyne COMSPHERE 3610 User Manual preview
COMSPHERE 3610
Brand: Paradyne Pages: 112
ADC HiGain HLU-231 List 8F Quick Installation preview
HiGain HLU-231 List 8F
Brand: ADC Pages: 7
Compaq StorageWorks AIT 35GB AutoLoader Overview And Installation preview
StorageWorks AIT 35GB AutoLoader
Brand: Compaq Pages: 4
Baicells EG2013B-M11 User Manual preview
EG2013B-M11
Brand: Baicells Pages: 10
Rainbow QPBB Instruction Manual preview
QPBB
Brand: Rainbow Pages: 2
Intercoax IXWB-450 Quick Start Manual preview
IXWB-450
Brand: Intercoax Pages: 2
Comway 4G DTU Configuration Instructions preview
4G DTU
Brand: Comway Pages: 20
ANEP P4GU VoLTE Technical Data Sheet preview
P4GU VoLTE
Brand: ANEP Pages: 48
ATEN Slideaway CL1008 User Manual preview
Slideaway CL1008
Brand: ATEN Pages: 77
Lattice Semiconductor sysCLOCK ECP5 Usage Manual preview
sysCLOCK ECP5
Brand: Lattice Semiconductor Pages: 43
Paradyne ACCULINK 3161 CSU Quick Reference Manual preview
ACCULINK 3161 CSU
Brand: Paradyne Pages: 19
Accusys ACS-7630 User Manual preview
ACS-7630
Brand: Accusys Pages: 34
Laser UDC CARD User Manual preview
UDC CARD
Brand: Laser Pages: 4
Oracle Acme Packet 3900 Hardware Installation And Maintenance Manual preview
Acme Packet 3900
Brand: Oracle Pages: 70
Hologic ThinPrep 3000 Operator'S Manual preview
ThinPrep 3000
Brand: Hologic Pages: 256
Robotis OpenCM 485 Manual preview
OpenCM 485
Brand: Robotis Pages: 10
National Instruments PXI-GPIB Getting Started preview
PXI-GPIB
Brand: National Instruments Pages: 45

Brands by name

Popular brands

Load more brands