Digital Equipment Alpha 21164PC Hardware Reference Manual Download Page 245

Page: 245 / 372

29 September 1997 – Subject To Change

Initialization and Configuration

7–11

Internal Processor Register Reset State

INTID

UNDEFINED

ASTRR

UNDEFINED PALcode must initialize.

ASTER

UNDEFINED PALcode must initialize.

SIRR

UNDEFINED PALcode must initialize.

HWINT_CLR

UNDEFINED PALcode must initialize.

ISR

UNDEFINED

SL_XMIT

Cleared

Appears on external pin.

SL_RCV

UNDEFINED

PMCTR

See Comments PMCTR<15:10> are cleared on reset. All other

bits are UNDEFINED.

MTU Registers

DTB_ASN

UNDEFINED PALcode must initialize.

DTB_CM

UNDEFINED PALcode must initialize.

DTB_TAG

Cleared

Valid bits are cleared on chip reset but not on
timeout reset.

DTB_PTE

UNDEFINED

DTB_PTE_TEMP

UNDEFINED

MM_STAT

UNDEFINED Must be unlocked by PALcode by reading VA

VA_FORM

UNDEFINED Must be unlocked by PALcode by reading VA

MVPTBR

UNDEFINED PALcode must initialize.

DC_PERR_STAT

UNDEFINED PALcode must initialize.

DTB_IAP

UNDEFINED

DTB_IA

UNDEFINED

DTB_IS

UNDEFINED

Table 7–2 Internal Processor Register Reset State

(Sheet 2 of 3)

IPR

Reset State

Comments

Summary of Contents for Alpha 21164PC





















































































































































































































































































































































































Search results

Summary of Contents for Alpha 21164PC

Reviews:

Brands by name

Popular brands

Digital Equipment Alpha 21164PC, Hardware Reference Manual

Search results

Summary of Contents for Alpha 21164PC

Reviews:

Brands by name

Popular brands