Digital Equipment Alpha 21164PC Hardware Reference Manual Download Page 111 | Manualshive

Page: 111 / 372

background image

29 September 1997 – Subject To Change

Clocks, Cache, and External Interface

4–23

21164PC-to-Bcache Transactions

Figure 4–10 Bcache Private Write Probe

4.6.5.2 Bcache Private Data-Write Operation

If a CPU-initiated write command hits in the Bcache, the data-write operation is
scheduled immediately. If the write hits clean, then the data-write operation must
update the tag state to dirty. If the write hits dirty, then the data-write operation does
not update the tag store.

If the CPU-initiated write command misses in the Bcache, the data-write is sched-
uled after the fill data from memory has returned. During the fill operation, the
Bcache tag store is updated to reflect the new tag and control state (modified). There-

FM-05561.AI4

index_h<21:4>

tag_ram_oe_l

st_clk

x_h

tag_ram_we_l

data_adsc_l

tag_data<32:19>

data_adv_l

data_ram_oe_l

data_ram_we_l<3:0>

data<127:0>

cpu_clk

0

1

2

3

4

5

6

7

8

bc_rd_latency (=5)

A0

T0

F

bc_clk_ratio (=3)

bc_clk_delay (=1)

Arrow indicates when the 21164PC

clocks Bcache probe data.

«
...
109
110
111
112
113
...
»

Summary of Contents for Alpha 21164PC





















































































































































































































































































































































































Reviews:

No comments

Related manuals for Alpha 21164PC

Brand: Data Translation Pages: 98

Brand: Ebyte Pages: 8

OfficeConnect WX2200

Brand: 3Com Pages: 204

Brand: Barco Pages: 121

Brand: Omega Engineering Pages: 34

Brand: ZALMAN Pages: 9

Brand: Patton electronics Pages: 145

Brand: Aviosys Pages: 77

Brand: ExtraHop Pages: 2

Brand: ADTRAN Pages: 136

Brand: ST Pages: 67

Blend PRO BP-2002

Brand: FOLSOM Pages: 89

Brand: Grundfos Pages: 40

Brand: IEI Technology Pages: 116

Dummy IC M3T-SSOP36B-450

Brand: Renesas Pages: 4

BD7682FJ-EVK-301

Brand: Rohm Pages: 6

Brand: Omron Pages: 172

Brand: Olivella Modular Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands