manualshive.com logo in svg

Digital Equipment Alpha 21164PC, Hardware Reference Manual

Share
Download
Digital Equipment Alpha 21164PC Hardware Reference Manual Download Page 194

5–46

Internal Processor Registers

29 September 1997 – Subject To Change

Memory Address Translation Unit (MTU) IPRs

5.2.16 Miss Address File Mode (MAF_MODE) Register (217)

MAF_MODE is a read/write register that controls diagnostic and test modes in the 
MTU miss address file (MAF). This register is cleared on chip reset. 
MAF_MODE<05> is also cleared on timeout reset. Figure 5–41 and Table 5–19 
describe the MAF_MODE register format.

Note:

The following bit settings are required for normal operation:

DREAD_NOMERGE = 0
WB_FLUSH_ALWAYS = 0
WB_NOMERGE = 0
MAF_ARB_DISABLE = 0
WB_CNT_DISABLE = 0

Figure 5–41 Miss Address File Mode (MAF_MODE) Register

PCA008

63

32

31

00

01

02

03

04

05

06

07

08

RAZ/IGN

RAZ/IGN

09

10

11

12

WB_CLR_LO_THRESH<1:0>

WB_SET_LO_THRESH<1:0>

DREAD_PENDING (Read-Only)
WB_PENDING (Read-Only)

MAF_ARB_DISABLE

WB_CNT_DISABLE

IO_NMERGE

WB_NOMERGE

WB_FLUSH_ALWAYS

DREAD_NOMERGE

Summary of Contents for Alpha 21164PC





















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands