manualshive.com logo in svg

Digital Equipment Alpha 21164PC, Hardware Reference Manual, Page: 160 / 372

Share
Download
Digital Equipment Alpha 21164PC Hardware Reference Manual Download Page 160

5–12

Internal Processor Registers

29 September 1997 – Subject To Change

Instruction Fetch/Decode Unit and Branch Unit (IDU) IPRs

5.1.12 Exception Address (EXC_ADDR) Register (10B)

EXC_ADDR is a read/write register used to restart the system after exceptions or 
interrupts. The HW_REI instruction causes a return to the instruction pointed to by 
the EXC_ADDR register. This register can be written both by hardware and soft-
ware. Hardware write operations occur as a result of exceptions/interrupts and 
CALL_PAL instructions. Hardware write operations that occur as a result of excep-
tions/interrupts take precedence over all other write operations.

In case of an exception/interrupt, hardware writes a program counter (PC) to this reg-
ister. In case of precise exceptions, this is the PC value of the instruction that caused 
the exception. In case of imprecise exceptions/interrupts, this is the PC value of the 
next instruction that would have issued if the exception/interrupt was not reported.

In case of a CALL_PAL instruction, the PC value of the next instruction after the 
CALL_PAL is written to EXC_ADDR.

Bit <00> of this register is used to indicate PALmode. On a HW_REI instruction, the 
mode of the system is determined by bit <00> of EXC_ADDR. Figure 5–11 shows 
the EXC_ADDR register format.

Figure 5–11 Exception Address (EXC_ADDR) Register

5.1.13 Exception Summary (EXC_SUM) Register (10C)

EXC_SUM is a read/write register that records the different arithmetic traps that 
occur between EXC_SUM write operations. Any write operation to this register 
clears bits <16:10>. Figure 5–12 and Table 5–4 describe the EXC_SUM register for-
mat.

00

31

PAL
RAZ/IGN

32

63

PC<63:2>

LJ-03483.AI4

PC<63:2>

Summary of Contents for Alpha 21164PC





















































































































































































































































































































































































Reviews:

No comments