manualshive.com logo in svg

Digital Equipment Alpha 21164PC, Hardware Reference Manual

Share
Download
Digital Equipment Alpha 21164PC Hardware Reference Manual Download Page 263

29 September 1997 – Subject To Change

Electrical Data

9–7

Clocking Scheme

allows a clock source of arbitrary dc bias to be ac coupled to the 21164PC. The peak-
to-peak amplitude of the clock source must be between 0.6 V and 3.0 V. Either a 
square-wave or a sinusoidal source may be used. Full-rail clocks may be driven by 
testers. In any case, the oscillator should be ac coupled to the osc_clk_in_h,l inputs 
by 47 pF through 220 pF capacitors.

Figure 9–2 shows a plot of the simulated impedance versus the clock input fre-
quency. Figure 9–1 is a simplified circuit of the complex model used to create
Figure 9–2.

Figure 9–2 Impedance vs Clock Input Frequency

Differential Impedance ocs_clk_in_h to osc_clk_in_l

LJ-04724.AI4

140

120

100

80

Impedance in Ohms

60

40

20

0

10

100

Frequency in MHz

1000

Summary of Contents for Alpha 21164PC





















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands