manualshive.com logo in svg

Digital Equipment Alpha 21164PC, Hardware Reference Manual

Share
Download
Digital Equipment Alpha 21164PC Hardware Reference Manual Download Page 276

9–20

Electrical Data

29 September 1997 – Subject To Change

AC Characteristics

Figure 9–8 is a timing diagram of an SROM load sequence.

Figure 9–8 Serial ROM Load Timing

The minimum srom_clk_h cycle = (126 

−

 sysclk ratio) × (CPU cycle time).

The maximum srom_clk_h to srom_data_h delay allowable (in order to meet the 
required setup time) = [126 

−

 (5 × sysclk ratio)] × (CPU cycle time).

9.4.5 Clock Test Modes

This section describes the 21164PC clock test modes.

9.4.5.1 Normal (1× Clock) Mode

When clk_mode_h<1> is not asserted, the osc_clk_in_h,l frequency is used to drive 
the input clock frequency. The clk_mode_h<0> signal is used to enable/disable a 
clock equalizing circuit, called a symmetrator. The symmetrator equalizes the duty-
cycle of the input clock for use onchip. The osc_clk_ in_h,l signals must have a duty 
cycle of at least 60/40 for the symmetrator to work properly. Normal clock mode 
with the symmetrator enabled is the preferred clocking mode of the 21164PC.

9.4.5.2 Clock Test Reset Mode

When clk_mode_h<1> is asserted, the sys_clk_out generator circuit is forced to 
reset to a known state. This allows the chip manufacturing tester to synchronize the 
chip to the tester cycle. This mode can be used with the symmetrator either enabled 
or disabled.

MK145507B

sys_reset_l

su

ho

t

t

su

t

ho

t

= 4 x sysclk 1.1 ns

= 0 ns

131, 072 Bits Total

srom_oe_l

srom_clk_h

srom_data_h

Summary of Contents for Alpha 21164PC





















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands