manualshive.com logo in svg

Digital Equipment Alpha 21164PC, Hardware Reference Manual

Share
Download
Digital Equipment Alpha 21164PC Hardware Reference Manual Download Page 107

29 September 1997 – Subject To Change

Clocks, Cache, and External Interface

4–19

21164PC-to-Bcache Transactions

Bcache timing is configured using the CBOX_CONFIG and CBOX_CONFIG2 
IPRs. Figures 5–48 and 5–51 show the layout of these registers. These registers are 
normally configured by 21164PC initialization code.

Both the 21164PC and system require access to the Bcache through a shared 128-bit 
data bus. When the 21164PC requires access to the Bcache (private mode), the 
st_clk is switched to the bc_clk regime where the clock is based on 
CBOX_CONFIG<BC_CLK_RATIO<3:0>. When the system requires access to the 
Bcache (system mode), the st_clk is switched to the sysclk regime where the clock is 
based on the sysclk ratio.

Table 4–6 describes the clocking regime and access type to the tag and data stores for 
each Bcache transaction.

System transactions include memory fills, Bcache victims, and system commands 
that require data movement. System transactions read and write the Bcache in the 
sys_clk regime (see Section 4.2.2). System Bcache read or write operations start rel-
ative to a sysclk edge. It is the responsibility of the system to control the rate of 
Bcache transactions by using the dack_h signal.

Private transactions include CPU-initiated read and write probes, CPU-initiated data 
writes, system probes, and system invalidates. Private transactions read and write the 
Bcache in the bc_clk regime (see Section 5.3.1). For private Bcache reads, both the 

1

A tag store write during a system data movement is conditional.

Table 4–6 Bcache Transactions

Bcache Access

Transaction

Clock Regime

Tag Store

Data Store

Memory Fill

System                      Write

Write

Bcache Victim

System

—

Read

System Data Movement

System

Write

1

Read

CPU Read Probe

Private

Read

Read

CPU Write Probe

Private

Read

—

System Probe

Private

Read

—

CPU Data Write-Dirty

Private

—

Write

CPU Data Write-Clean

Private

Write

Write

Invalidate-Hit

Private

Write

—

Summary of Contents for Alpha 21164PC





















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands