manualshive.com logo in svg

Digital Equipment Alpha 21164PC, Hardware Reference Manual, Page: 207 / 372

Share
Download
Digital Equipment Alpha 21164PC Hardware Reference Manual Download Page 207

29 September 1997 – Subject To Change

Internal Processor Registers

5–59

External Interface Control (CBU) IPRs

5.3.1 CBU Configuration (CBOX_CONFIG) Register (FF FFF0 0008)

CBOX_CONFIG is a read/write register that controls Bcache activity. Figure 5–48 
and Table 5–26 describe the CBOX_CONFIG register format. The bits in this regis-
ter are initialized to the value indicated in Table 5–26 on reset, but not on timeout 
reset.

Figure 5–48 CBU Configuration (CBOX_CONFIG) Register

Table 5–26 CBU Configuration Register Fields

(Sheet 1 of 3)

Name

Extent

Type

Description

Reserved

<03:00>

RW,0

Reserved to DIGITAL. Must be zero (MBZ).

BC_CLK_
RATIO<3:0>

<07:04>

RW,3

This field determines the Bcache clock period 
(st_clk) in number of CPU cycles. At power-up, the 
st_clk remains 0 until the Bcache is enabled. The 
supported range of values is 2 to10.

BC_
LATENCY_
OFF<3:0>

<11:08>

RW,0

This offset field determines the number of CPU 
cycles to wait from the CPU clock edge that launches 
the index until the data is latched into the 21164PC. 
(Total Latency = 5 + BC_LATENCY_OFF<3:0>.) 
At power-up, this field is initialized to 0, which rep-
resents a total Bcache latency of five CPU cycles. 
The supported range of values for this field is 0 to15, 
which provides a total latency range of 5 to 20 CPU 
cycles.

PCA004

31

00

63

32

07

12 11

16 15

18

19

20

23

24

25

26

27

28

30

MBZ

08

MBZ

04 03

22

14 13

BC_LATENCY_OFF<3:0>

BC_CLK_DELAY<1:0>
BC_RW_OFF<2:0>
BC_PROBE_UNDER_FILL
BC_FILL_DLY_OFF<2:0>
IO_PARITY_ENABLE
MEM_PARITY_ENABLE
BC_FORCE_HIT
BC_FORCE_ERR
BC_BIG_DRV

BC_SIZE<1:0>

BC_TAG_DATA<2:0>
BC_ENABLE

BC_CLK_RATIO<3:0>

Summary of Contents for Alpha 21164PC





















































































































































































































































































































































































Reviews:

No comments