manualshive.com logo in svg

Digital Equipment Alpha 21164PC, Hardware Reference Manual, Page: 174 / 372

Share
Download
Digital Equipment Alpha 21164PC Hardware Reference Manual Download Page 174

5–26

Internal Processor Registers

29 September 1997 – Subject To Change

Instruction Fetch/Decode Unit and Branch Unit (IDU) IPRs

5.1.26 Serial Line Receive (SL_RCV) Register (117)

SL_RCV is a read-only register used to receive bit-serial data under the control of a 
software timing loop. The RCV bit in the SL_RCV register is functionally connected 
to the srom_data_h signal. A serial line interrupt is requested whenever a transition 
is detected on the srom_data_h signal and the SLE bit in the ICSR is set. During 
normal operations (not in test mode), the srom_data_h signal serves both the serial 
line reception and the Icache SROM interface (see Sections 7.4 and 7.5). 
Figure 5–25 and Table 5–10 describe the SL_RCV register format.

Figure 5–25 Serial Line Receive (SL_RCV) Register

Table 5–10 Serial Line Receive Register Fields

Name

Extent

Type

Description

RCV

<06>

RO

Serial line receive data

00

05

06

07

31

32

63

LJ-03498.AI4

RCV

RAZ

RAZ

RAZ

Summary of Contents for Alpha 21164PC





















































































































































































































































































































































































Reviews:

No comments