Digital Equipment Alpha 21164PC Hardware Reference Manual Download Page 193 | Manualshive

Page: 193 / 372

background image

29 September 1997 – Subject To Change

Internal Processor Registers

5–45

Memory Address Translation Unit (MTU) IPRs

Table 5–18 Dcache Mode Register Fields

Name

Extent

Type

Description

DC_ENA

<00>

RW,0

Software Dcache enable. When set, the
DC_ENA bit enables the Dcache. When clear,
the Dcache command is not updated by ST or
FILL operations, and all LD operations are
forced to miss in the Dcache. Must be one
(MBO) in normal operation.

DC_FHIT

<01>

RW,0

Dcache force hit. When set, the DC_FHIT bit
forces all Dstream references to hit in the
Dcache. Must be zero in normal operation.

DC_BAD_
PARITY

<02>

RW,0

When set, the DC_BAD_PARITY bit inverts the
data parity inputs to the Dcache on integer
stores. This has the effect of putting bad data
parity into the Dcache on integer stores that hit
in the Dcache. This bit has no effect on the tag
parity written to the Dcache during FILL opera-
tions, or the data parity written to the CBU write
data buffer on integer store instructions.

Floating-point store instructions should not be
issued when this bit is set because it may result
in bad parity being written to the CBU write data
buffer. Must be zero (MBZ) in normal operation.

DC_PERR_
DISABLE

<03>

RW,0

When set, the DC_PERR_DISABLE bit disables
Dcache parity error reporting. When clear, this
bit enables all Dcache tag and data parity errors.
Parity error reporting is enabled during all other
Dcache test modes unless this bit is explicitly
set. Must be zero (MBZ) in normal operation.

«
...
191
192
193
194
195
...
»

Summary of Contents for Alpha 21164PC





















































































































































































































































































































































































Reviews:

No comments

Related manuals for Alpha 21164PC

AllShare Cast Dongle

Brand: Samsung Pages: 2

Brand: D-Link Pages: 14

Brand: 3xLogic Pages: 2

Brand: Lab.gruppen Pages: 35

Brand: CSS Pages: 2

Brand: NXP Semiconductors Pages: 24

Brand: Juniper Pages: 7

Brand: National Instruments Pages: 130

Brand: Loopcomm Pages: 2

Brand: Alcatel-Lucent Pages: 60

Brand: AMD Pages: 27

Brand: EXAGATE Pages: 7

Brand: Flexwatch Pages: 13

ExtremeCloud Appliance E3120

Brand: Extreme Networks Pages: 27

Brand: IEI Technology Pages: 213

Brand: SeaLevel Pages: 25

Magellan Systems

Brand: Paradox Pages: 40

Brand: Asus Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands