manualshive.com logo in svg

Digital Equipment Alpha 21164PC, Hardware Reference Manual

Share
Download
Digital Equipment Alpha 21164PC Hardware Reference Manual Download Page 214

5–66

Internal Processor Registers

29 September 1997 – Subject To Change

External Interface Control (CBU) IPRs

DBG_SEL=0 DBG_SEL=1

spa req

spc != NOP

replay req

scc code<0>

io_wr or 
rmv req

scc code<1>

BC_THREE_MISS

<6>

RW,0 Allow three read misses to be launched to the system. This 

feature assumes the system can guarantee that fills can be 
returned in order.

Reserved

<7>

RW,0 Reserved to DIGITAL. Must be zero (MBZ).

PM0_MUX<2:0>

<10:8>

RW,0 This field selects the CBU events used for performance 

counter #0.

PM0_MUX
<2:0>

Counter 0 is used to count:

0x0

Total Bcache read requests (the total number 
of read requests from the MTU).

0x1

Bcache Dstream read hits (total number of 
Dstream read requests that hit in the  Bcache).

0x2

Bcache Dstream read fills (the total number of 
Dstream read fill requests to the Bcache).

0x3

Bcache write operations (the total number of 
write requests from the MTU).

0x4

Undefined.

0x5

Bcache clean write hits (the total number of 
write operations that hit a clean block in the 
Bcache).

0x6

Bcache victims (the total number of VICTIM 
commands issued by the 21164PC).

0x7

Read miss 2 launched (the number of times a 
second READ MISS request is sent to the sys-
tem while there is already an outstanding 
READ MISS command).

Table 5–29 CBU Configuration #2 Register Fields

(Sheet 2 of 3)

Name

Extent

Type

Description

Summary of Contents for Alpha 21164PC





















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands