Dell Inspiron XPS Service Manual Download Page 1

Page: 1 / 120

Dell™ Inspiron™ XPS Service Manual

Before You Begin

System Components

Optical Drive

Hard Drive

Memory Module

Modem

Mini PCI Card

Internal Card With Bluetooth

Wireless Technology

Center Control Cover

Keyboard

Display

Palm Rest

Speakers

Subwoofer

USB Port Board

System Fans

Microprocessor Thermal-Cooling Assembly

Microprocessor Module

Video Card/Thermal Cooling Assembly

MCH Heat Sink

PC Card Reader Cage

System Board

Battery Latch Assembly

Customizable LEDs

Flashing the BIOS

Pin Assignments for I/O Connectors

Notes, Notices, and Cautions

Abbreviations and Acronyms

For a complete list of abbreviations and acronyms, see the

Dell Inspiron Help

file. To access the help file, click the

Start

button, click

Help and Support

, click

User and system guides

, click

User's guides

, and click

Dell Inspiron Help

If you purchased a Dell™ n Series computer, any references in this document to Microsoft®

Windows

operating systems are not applicable.

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc.

is strictly forbidden.

Trademarks used in this text:

Dell

, the

DELL

logo, and

Inspiron

are trademarks of Dell Inc.;

Microsoft

and

Windows

are registered trademarks of Microsoft Corporation;

Bluetooth

is a

trademark owned by Bluetooth SIG, Inc. and is used by Dell Inc. under license.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.

Model PP14L

February 2005 Rev. A00

NOTE:

A NOTE indicates important information that helps you make better use of your computer.

CAUTION:

A CAUTION indicates a potential for property damage, personal injury, or death.

Summary of Contents for Inspiron XPS

























































































































Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands

Dell Inspiron XPS, Service Manual

Search results

Summary of Contents for Inspiron XPS

Reviews:

Related manuals for Inspiron XPS

Brands by name

Popular brands