Related
Commands
access-class
– restricts the incoming connections to a particular IP address in an IP access
control list (ACL).
password
– specifies a password for users on terminal lines.
show linecard
– displays the line card(s) status.
linecard
Pre-configure a line card in a currently empty slot of the system or a different line card type for the slot. To pre-configure
a 4-port 40G line card, refer to the
linecard
command.
C-Series, E-Series
Syntax
linecard
number card-type
Parameters
number
Enter the number of the slot. For the C-Series, the range is 0 to 7. For
the E-Series, the range is 0 to 13 on the E1200/E1200i, 0 to 6 on the
E600/E6001, and 0 to 5 on the E300..
card-type
Enter the line card ID (refer to the “Supported Hardware” section in
the
Release Notes
).
Defaults
Not configured
Command Modes
CONFIGURATION
Command History
Version 8.1.1.2
Introduced on the E-Series ExaScale E600i.
Version 8.1.1.0
Introduced on the E-Series ExaScale E1200i.
Version 7.5.1.0
Introduced on the C-Series.
E-Series
Original command
Usage
Information
Use this command only for empty slots or a slot where you have hot-swapped a different line
card type. Before inserting a card of a different type into the pre-configured slot, execute the
no linecard number
command. The examplet shows the current supported C-Series line
cards, along with their “card types” (card-type IDs).
NOTE: It is advisable to shut down interfaces on a line card that you are hot-swapping.
Example
FTOS#show linecard 3
-- Line card 11 --
Status : not present
FTOS#linecard 3 ?
E46TB 36-port GE 10/100/1000Base-T with RJ45 - 8-port FE/GE
with SFP - 2-port
10GE with SFP+
E46VB 36-port GE 10/100/1000Base-T with RJ45 and PoE - 8-port
FE/GE with SFP -
2-port 10GE with SFP+
E48PB 48-port FE/GE line card with SFP optics (CB)
122
Summary of Contents for Force10 Z9000
