source
Enter the IP address in dotted decimal format of the network from
which the packet was sent.
mask
(OPTIONAL) Enter a network mask in /prefix format (/x) or A.B.C.D.
The mask, when specified in A.B.C.D format, may be either
contiguous or non-contiguous.
any
Enter the keyword
any
to specify that all routes are subject to the
filter.
host
ip-address
Enter the keyword
host
and then enter the IP address to specify a
host IP address or hostname.
destination
Enter the IP address of the network or host to which the packets are
sent.
count
(OPTIONAL) Enter the keyword
count
to count packets processed
by the filter.
byte
(OPTIONAL) Enter the keyword
byte
to count bytes processed by
the filter.
log
(OPTIONAL, E-Series only) Enter the keyword
log
to enter ACL
matches in the log.
dscp
(OPTIONAL) Enter the keyword
dcsp
to match to the IP DCSCP
values.
order
(OPTIONAL) Enter the keyword
order
to specify the QoS priority for
the ACL entry. The range is 0 to 254 (where 0 is the highest priority
and 254 is the lowest; lower order numbers have a higher priority). If
you do not use the keyword
order
, the ACLs have the lowest order
by default (255).
monitor
(OPTIONAL) Enter the keyword
monitor
when the rule is describing
the traffic that you want to monitor and the ACL in which you are
creating the rule is applied to the monitored interface.
NOTE: For more information, refer to the Flow-based Monitoring
section in the Port Monitoring chapter of the
FTOS Configuration
Guide
.
fragments
Enter the keyword
fragments
to use ACLs to control packet
fragments.
Defaults
Not configured.
Command Modes
CONFIGURATION-EXTENDED-ACCESS-LIST
Command History
Version 8.3.11.1
Introduced on the Z9000.
Version 8.3.7.0
Introduced on the S4810.
Version 8.3.1.0
Add the DSCP value for ACL matching.
Version 8.2.1.0
Allows ACL control of fragmented packets for IP (Layer 3) ACLs.
Version 8.1.1.0
Introduced on the E-Series ExaScale.
242
Summary of Contents for Force10 Z9000
