007
LCP copy
Value:
No copying (NO COPY)
[0]
Upload all parameters (UPL. ALL PAR.)
[1]
Download all parameters (DWNL. ALL PAR.)
[2]
Download size-independent parameters
(DWNL.OUTPIND.PAR.)
[3]
Function:
Parameter 007
LCP copy
is used if you want to use the LCP 2 control
panel's integral copy function. The function is used if you want to copy
all parameter setups from one adjustable frequency drive to another by
moving the LCP 2 control panel.
Description of choice:
Select
Upload all parameters
[1] if you want all parameter values to be
transferred to the control panel. Select
Download all parameters
[2] if all
parameter values transferred are to be copied to the adjustable frequency
drive to which the control panel is attached. Select
Download size-inde-
pendent par.
[3] if you only want to downloade the size-independent
parameters. This is used when downloading to a adjustable frequency
drive with a different rated power size than that from which the param-
eter setup originates.
NB!
Upload/download can only be performed in stop mode.
Download can only be performed to a adjustable fre-
quency drive with the same software version number,
see parameter 626
Database identification no.
008
Display scaling of output frequency
Value:
0.01 - 100.00
1.00
Function:
In this parameter, the factor is selected by which the output frequency is
to be multiplied. The value is shown in the display, provided parameters
009-012
Display readout
have been set to
Output frequency x scaling
[5].
Description of choice:
Set the required scaling factor.
009
Large display readout
Value:
No readout (none)
[0]
Resulting reference [%]
(reference [%])
[1]
Resulting reference [unit]
(reference [unit])
[2]
Feedback [unit] (feedback [unit])
[3]
Frequency [Hz] (Frequency [Hz])
[4]
Output frequency x scaling
(frequency x scale)
[5]
Motor current [A] (Motor current [A])
[6]
Torque [%] (Torque [%])
[7]
Power [kW] (Power [kW])
[8]
Power [HP] (Power [HP][US])
[9]
Motor voltage [V]
(Motor voltage [V])
[11]
DC link voltage [V]
(DC link voltage [V])
[12]
Thermal load motor [%]
(Motor thermal [%])
[13]
Thermal load [%]
(FC. thermal[%])
[14]
Running hours [Hours]
(RUNNING HOURS])
[15]
Digital input [Bin]
(Digital input[bin])
[16]
Analog input 53 [V]
(analog input 53 [V])
[17]
Analog input 60 [mA]
(analog input 60 [mA])
[19]
Pulse reference [Hz]
(Pulse INPUT 33. [Hz])
[20]
External reference [%]
(external ref. [%])
[21]
Status word [Hex] (Status word [hex])
[22]
Heatsink temperature [°C]
(Heatsink temp [°C])
[25]
Alarm word [Hex] (Alarm word [hex])
[26]
Control word [Hex] (Control word [Hex])
[27]
Warning word [Hex]
(warning word [Hex])
[28]
Extended status word [Hex]
(Ext. status [hex])
[29]
Communication option card warning
(COMM OPT WARN [HEX])
[30]
Pulse count
(PULSE COUNTER)
[31]
Pulse input 29
(PULSE INPUT 29)
[32]
Function:
In this parameter you can select the data value that you wish to display
in the LCP control unit display line 2 when the frequency converter is
switched on. The display will also be included in the scrollbar in display
mode. In parameters 010-012
Display readout
you can select a further
three data values, which are displayed in display line 1.
Description of choice:
No readout
can only be selected in parameters 010-012
Small display
readout
.
Resulting reference [%]
gives, as a percentage, the resulting reference
in the range from Minimum reference, Ref
MIN
to Maximum reference,
Ref
MAX
.
Reference [unit]
gives the resulting reference with unit Hz in
Open loop
.
In
Closed loop
the reference unit is selected in parameter 416
Process
units
.
Feedback [unit]
gives the resulting signal value using the unit/scaling
selected in parameter 414
Minimum feedback, FB
LOW
, 415
Maximum
feedback, FB
HIGH
and 416
Process units
.
Frequency [Hz]
gives the output frequency of the frequency converter.
4 Programming
VLT
®
Decentral FCD 300 Design Guide
68
MG.90.S1.02 - VLT
®
is a registered Danfoss trademark
4
