manualshive.com logo in svg

D-Link DES-6300, User Manual, Page: 25 / 298

Share
Download
D-Link DES-6300 User Manual Download Page 25

Modular L3 Ethernet Switch User’s Guide

 

16 

 

DES-6309 GBIC Module 

 

Figure 3- 8. Two-port GBIC Module 

 

Two-port, front-panel module 

 

Connects to GBIC devices at full duplex 

 

GBIC Ethernet ports 

 

Fully compliant with IEEE 802.3z 

 

Supports full-duplex operation only 

 

IEEE 802.3x-compliant Flow Control support 

Power Supply Modules 

 

Dual power modules design with current sharing design 

 

Full redundant feature design to ensure continuous operation 

 

If one power module failed, the other will take over all current supply 

automatically. 

 

Hot-swappable/Hot-pluggable capability 

 

Power management functions 

 

Input: 90 ~ 264 VAC, 47 ~ 63Hz 

 

Output: 3.3V: 80A Max 

 

12V: 2A Max 

Led Indicators 

The LED indicators of the Switch include CPU Status and Power OK. The following shows the 
LED indicators for the Switch along with an explanation of each indicator. 

 

Figure 3- 9.  CPU Front Panel LED Indicators 

 

CPU Status

 – This center indicator on the front panel displays the current status 

of the switch. The LED will blink while the Power-On Self-Test (POST) is 
running during startup. It will light a steady green after the POST test to indicate 
the switch is powered on and operating properly. It will light amber when an error 
occurs during startup and the switch is therefore not functioning.  

Summary of Contents for DES-6300











































































































































































































































































































Reviews:

No comments