manualshive.com logo in svg

D-Link DES-6300, User Manual, Page: 211 / 298

Share
Download
D-Link DES-6300 User Manual Download Page 211

Modular L3 Ethernet Switch User’s Guide

 

202 

 

5. Complete 

the 

IPX RIP Parameters

 window fields if required. 

6. Click  . Close the 

IPX RIP Parameters

 window. The 

IPX Router Interface 

Parameters Edit

 window opens. 

 
7. Click 

the 

SAP Parameters

 button to modify IPX SAP parameters. The 

IPX SAP 

Parameters

 window opens: 

 

 

Figure 6- 159.  IPX SAP Parameters window 

 
The 

IPX SAP Parameters

 window displays the following parameters: 

 

 

Update Interval – 

SAP periodic update interval, in seconds. Set to 0 to disable 

periodic messages. When set to 0, all entries learned on this interface are not aged 
out. 

 

Age Multiplier – 

Holding multiplier for information received in SAP periodic 

updates. This value multiplied by the update interval defines how many seconds 
SAP information remains without being refreshed. Set to 0 to prevent the entries 
learned on this interface from being aged out. 

 

Respond to Get Nearest Server – 

Defines whether the device responds to SAP 

“get nearest server” requests received on this circuit. 

 

Status  –

 Defines whether the SAP interface is active. OFF is inactive but not 

deleted. 

 

Note:  

The Update Interval multiplied by the Age Multiplier must be less than 2 million

 

 

8. Complete 

the 

IPX SAP Parameters

 window fields if required. 

 

9. Click. 

Close 

the 

IPX SAP Parameters

 window. The 

IPX Router Interface 

Parameters Edit

 window is displayed. 

 

10. Edit the fields. 

 

11. Click 

. 

 

12. Close the 

IPX Router Interface Parameters Edit

 window. The 

IPX Router Interface 

Parameters

 window opens. 

 

Summary of Contents for DES-6300











































































































































































































































































































Reviews:

No comments