manualshive.com logo in svg

D-Link DES-6300, User Manual, Page: 13 / 298

Share
Download
D-Link DES-6300 User Manual Download Page 13

Modular L3 Ethernet Switch User’s Guide

 

4 

 

 

Chassis features include

: 

 

• 

Six slots for installing networking modules (plus one slot reserved for the CPU) 

• 

Two slots for installing redundant power supply modules 

• 

31.99 Gigabit/sec. (Gbps) backplane switching fabric 

• 

Hot-swappable design for power supply modules 

• 

Networking modules warm-swappable (except CPU module)  

• 

Ears and screws for rack mounting 

Switch Modules 

The plug-in modules available for the switch are optional except for the CPU module. These 
modules are described below: 

CPU Module 

A single CPU module must be present and must be installed in first (uppermost) slot. 

Layer 2 Support Includes: 

 

Layer 2 switching based on MAC address & VLAN ID 

 

Store and Forward packet switching 

 

Broadcast Storm rate filtering 

 

Supports static filtering (based on MAC address) 

 

Supports IEEE 802.1Q VLAN  

 

Proprietary simplified Port-based VLANs 

 

IEEE 802.1d Spanning Tree support 

 

Address table: 64K MAC address per switch 

 

Supports 802.1p priority queuing  

 

Port Aggregation (Port-Trunking) Capability 

 

Port Mirroring 

 

IGMP snooping  

 

RS-232 port for out-of-band management and system configuration 

 

Telnet Remote Configuration 

 

TFTP software upgrades, settings file and switch log uploads 

 

NMS (Net Management System)  

 

CLI (Command Line Interface) 

 

SNMP Agents:  

 

MIB-II (RFC 1213) 

 

RMON MIB (RFC 1757) 

 

Bridge MIB (RFC 1493) 

 

Supports four RMON (1, 2, 3, 9) groups 

 

BootP support 

Layer 3 Support Includes: 

 

Support RIP1 and RIP2 routing protocol 

 

Support OSFP routing protocol 

 

Support IGMP, IP Multicast packet filtering, support QoS (Quality of Service) 

 

Support Multicast Routing protocol: PIM DM 

 

Support Layer 3 Access Control List, (ACL) 

Summary of Contents for DES-6300











































































































































































































































































































Reviews:

No comments