D-Link DES-6300 User Manual Download Page 14

Page: 14 / 298

Modular L3 Ethernet Switch User’s Guide

Optional Modules

DES-6303 10BASE-T/100BASE-TX Module

Sixteen 10BASE-T/100BASE-TX ports

Fully compliant with IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX

All 10/100Mbps ports support NWay auto-negotiation

Back pressure Flow Control support for half-duplex mode

IEEE 802.3x-compliant Flow Control support for full duplex

DES-6304 100BASE-FX (MT-RJ) Module

Twelve 100BASE-FX (MT-RJ) Fast Ethernet ports

Fully compliant with IEEE 802.3u 100BASE-FX

IEEE 802.3x compliant Flow Control support for full duplex

DES-6305 100BASE-FX (SC) Module

Eight 100BASE-FX (SC) Fast Ethernet ports

Connects to a 100BASE-FX device at full duplex.

Fully compliant with IEEE 802.3u 100BASE-FX

Supports Full-duplex operation only

02.3x-compliant Flow Control support

DES-6306 1000BASE-SX (SC) Module

Two 1000BASE-SX (SC) Gigabit Ethernet ports

Fully compliant with IEEE 802.3z

Support full-duplex operation only

IEEE 802.3x-compliant Flow Control support

DES-6307 1000BASE-LX (SC) Module

Two 1000BASE-LX (SC) Gigabit Ethernet ports

Fully compliant with IEEE 802.3z

Support full-duplex operation only

IEEE 802.3x-compliant Flow Control support

DES-6308 1000BASE-T (RJ-45) Module

Two 1000BASE-T Gigabit Ethernet ports

Connects to 1000BASE-T devices only at full duplex and auto-negotiating

10/100/1000 Mbps ports

Fully compliant with IEEE 802.3ab

Fully compliant with IEEE 802.1Q/P

Back pressure Flow Control support for half-duplex mode

IEEE 802.3x compliant Flow Control support for full duplex

DES-6309 GBIC Module

Two GBIC Ethernet ports

Fully compliant with IEEE 802.3z

Support full-duplex operation only

IEEE 802.3x-compliant Flow Control support

Summary of Contents for DES-6300











































































































































































































































































































Search results

Summary of Contents for DES-6300

Reviews:

D-Link DES-6300, User Manual, Page: 14 / 298

Search results

Summary of Contents for DES-6300

Reviews: