Comtrol WR7802-XT Series User Manual Download Page 46

Page: 46 / 128

44 - Status | Network Flow Page

RocketLinx WR7802-XT Series User Guide

: 2000638 Rev. A

Configuration Using the Web User Interface

Status | Network Flow Page

The

Network Flow

shows the packet counters for transmission and reception for the Cellular interface.(3G or

LTE).

Cellular Settings

SIM1 Status

SIM2 Status

This defines the possible SIM status messges:

•

SIM OK: The SIM card is ready to use.

•

SIM Carrier Inserted: The SIM card is not inserted.

•

SIM PIN Locked: The SIM card is locked due to PIN error. It may be
caused by error typing PIN password many times. Check with your ISP
to resolve the issue.

•

SIM is deactivated: The SIM card may have some problem. Please check
with your ISP to resolve the issue.

Connection Status

•

Connected: The 3G/LTE interface is connected to the base station.

•

Not Connected: The 3G/LTE interface is not connected to the base
station.

IP Address

This is the Cellular IP address assigned by the ISP.

Network Flow Page

Poll Interval

The Poll Interval time setting, ranges from 0~65524 seconds. If you want
to change the

Poll Interval

time, click the

Stop

button,

enter a new value,

and click

Set Interval

to activate.

Set Interval

Click this button to set a new interval time after entering a new polling
interval time.

Stop

Click this button to stop polling the associated clients.

Refresh

Click to refresh the table.

Beta

Version

Summary of Contents for WR7802-XT Series

































































































































Search results

Summary of Contents for WR7802-XT Series

Reviews:

Related manuals for WR7802-XT Series

Brands by name

Popular brands

Comtrol WR7802-XT Series, User Manual

Search results

Summary of Contents for WR7802-XT Series

Reviews:

Related manuals for WR7802-XT Series

Brands by name

Popular brands