Comtrol WR7802-XT Series User Manual Download Page 90 | Manualshive

Page: 90 / 128

background image

88 - Cellular | Cellular Basic Settings Page

RocketLinx WR7802-XT Series User Guide

: 2000638 Rev. A

Configuration Using the Web User Interface

Note:

You must

Save

) settings, if you want to maintain these settings if the WR7802-XT is rebooted.

Cellular Basic Settings

Disable Cellular
Interface

You can disable the Cellular interface manually.

SIM Selection

SIM 1 means the SIM Socket 1, you can see the ID in the front panel. SIM 2 means
the SIM Socket 2.

Select one of SIM sockets as the startup SIM socket. SIM 1 is the default settings.
Make sure that you insert the SIM card to the SIM socket you select.

Note:

The LTE module only can check the selected SIM slot. Thus the unselected
SIM2 slot shows as inserted because the SIM holder is inserted.

Cellular
Redundant

If you enable

Cellular Redundant

, you must insert both SIM cards into the two SIM

sockets before powering on the system or you should reboot the WR7802-XT.

If enabled, the two SIMs are redundant with each other if the primary Cellular
connection fails. The selected SIM number is the primary SIM, the other one is
backup SIM. The redundant timer is based on your settings of Reconnection Delay
and Retries.

Note:

Adjust the Reconnection Delay and Retires based on your application, if you
requests shorter redundant time, you can modify the delay time or retires
times.

APN

Every ISP has a specific APN (Access Point Name) assigned to its Cellular
network. If necessary, check with your ISP to determine the APN and correctly
enter the value on this page.

If you fail to connect to the Cellular network, this should be the first setting that
you verify.

User Name

The user name for the Cellular connection. If applicable, this is normally provided
by your ISP.

Password

The password for the Cellular connection. If applicable, this is normally provided
by your ISP.

Authentication
Type

You can select CHAP or PAP per your ISP request. If applicable, this is normally is
provided by your ISP.

Connection

You can select

Connect

to re-connect the Cellular connection of the selected SIM

card. This progress may take 30 seconds. You will see a pop-up message notifying
that you need to wait 30 seconds.

Beta

Version

«
...
88
89
90
91
92
...
»

Summary of Contents for WR7802-XT Series

































































































































Reviews:

No comments

Related manuals for WR7802-XT Series

Brand: LAWO Pages: 154

Brand: Oracle Pages: 24

Brand: Ruckus Wireless Pages: 56

Fan Tray 8820-S2-900

Brand: Paradyne Pages: 6

Brand: red lion Pages: 5

Brand: MiWire Pages: 24

Brand: Planet Pages: 2

Brand: Altimium Pages: 12

Security Router X-PeditionTM

Brand: Enterasys Pages: 466

TeraStation WSS WS5020N6

Brand: Buffalo Pages: 115

Brand: EMC Pages: 88

Brand: ZyXEL Communications Pages: 191

RuggedSwitch RS500

Brand: RuggedCom Pages: 16

EdgePoint EP-R8

Brand: Ubiquiti Pages: 22

Brand: Westermo Pages: 28

Brand: l-com Pages: 11

Brand: NetComm Wireless Pages: 154

Brand: OWC Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands