Comtrol WR7802-XT Series User Manual Download Page 69

Page: 69 / 128

RocketLinx WR7802-XT Series User Guide

: 2000638 Rev. A

Switch Configuration | VLAN Configuration Page - 67

Configuration Using the Web User Interface

Note:

You must

Save

(

Page 115

) settings, if you want to maintain these settings if the WR7802-XT is rebooted.

VLAN Configuration Page

PVID Setting

PVID is the abbreviation of the Port VLAN ID.

Enter the port VLAN ID in this field. PVID allows the switches to
identify which port belongs to which VLAN.

To keep things simple, it is recommended that PVID is equivalent to
VLAN IDs. The values of PVIDs are from 1 to 4095.

1 (default value) and 4095 are reserved and you cannot enter these two
PVIDs.

Click the

Apply

button to activate the PVID settings.

Management VLAN
ID

The management VLAN ID is the VLAN ID of the CPU interface so that
only member ports of the management VLAN can ping and access the
router. The default management VLAN ID is 1.

Add Static VLAN

Assign VLAN ID for a new VLAN and specify the egress (outgoing) rule
to be

Untag

Tag

on each port.

Untag

: Indicates that egress/outgoing frames are not VLAN tagged.

Tag

: Indicates that egress/outgoing frames are to be VLAN tagged.

: Not available

Press the

Apply

button to activate settings.

Static VLAN
Overview

The table shows static VLAN status.

Check

Select

if you want to use the

Delete Selected

button to delete the

selected entry.

Edit

: Edit entries for the Route Entry.

Delete

all: Delete the all entries.

Refresh

: Reload the table.

Beta

Version

Summary of Contents for WR7802-XT Series

































































































































Search results

Summary of Contents for WR7802-XT Series

Reviews:

Related manuals for WR7802-XT Series

Brands by name

Popular brands

Comtrol WR7802-XT Series, User Manual

Search results

Summary of Contents for WR7802-XT Series

Reviews:

Related manuals for WR7802-XT Series

Brands by name

Popular brands