Comtrol WR7802-XT Series User Manual Download Page 108

Page: 108 / 128

106 - Management | Remote Settings Page

RocketLinx WR7802-XT Series User Guide

: 2000638 Rev. A

Configuration Using the Web User Interface

Note:

You must

Save

(

Page 115

) settings, if you want to maintain these settings if the WR7802-XT is rebooted.

Configure SNMPv3 User Profile

Configure
SNMPv3 User
Profile

For SNMP protocol version 3,
click the Configure SNMPv3
User Profile link (in blue) to
configure the details of the
SNMPv3 user.

Enable
SNMPv3
Admin/User

Click the check box to enable the
SNMPv3 user profile.

User Name

Specify a user name for the
SNMPv3 administrator or user.
Only the SNMP commands
carrying this user name are
allowed to access the device.

Password

Specify a password for the
SNMPv3 administrator or user.
Only the SNMP commands
carrying this password are
allowed to access the device.

Access Type

Select

Read Only

Read and

Writ

e accordingly.

Authentication
Protocol

Select an authentication
algorithm.

SHA

authentication is

stronger than

MD5

but it is

slower.

Privacy
Protocol

Specify the encryption method
for SNMP communications.

None

and

DES

are available, the

default is

None

Apply

Click the

Apply

button to apply

the configuration changes.

Beta

Version

Summary of Contents for WR7802-XT Series

































































































































Search results

Summary of Contents for WR7802-XT Series

Reviews:

Related manuals for WR7802-XT Series

Brands by name

Popular brands

Comtrol WR7802-XT Series, User Manual

Search results

Summary of Contents for WR7802-XT Series

Reviews:

Related manuals for WR7802-XT Series

Brands by name

Popular brands