Comtrol WR7802-XT Series User Manual Download Page 19

Page: 19 / 128

RocketLinx WR7802-XT Series User Guide

: 2000638 Rev. A

LED Descriptions - 17

Hardware Installation

LED Descriptions

This subsection provides information about the WR7802-XT LEDs.

Reset Button

The WR7802-XThas a reset button that you can use to reboot the WR7802-XT or reset the configuration to the
factory default.

The

Reset

button is located on the front panel of the WR7802-XT below the second SFP port.

LED

Indication

Blinking

Off

PWR

PWR1/PWR2 Status

N/A

Valid power applied

No power

Fiber Port GF1/GF2 Status

GF is activating

GF is linked up

No link

PoE

PoE Output Status

N/A

Delivering PoE power

No PD is attached

ETH

Eth1/Eth2 Status

Port is
activating

Port is linked up

Port not linked up

Digital Output Status

N/A

The Relay is ON. It
may indicate the
alarm of specific
events.

The Relay is OFF

Boot Status

Booting

LTE connected

Boot finished

SYS

System Status

N/A

Power on

Power off

Reset Button

Description

Depress 0-3 Seconds

This reboots the WR7802-XT without changing the
configuration.

Depress > 7 Seconds

This loads the factory default configuration values into the
WR7802-XT including the IP address.

Beta

Version

Summary of Contents for WR7802-XT Series

































































































































Search results

Summary of Contents for WR7802-XT Series

Reviews:

Related manuals for WR7802-XT Series

Brands by name

Popular brands

Comtrol WR7802-XT Series, User Manual

Search results

Summary of Contents for WR7802-XT Series

Reviews:

Related manuals for WR7802-XT Series

Brands by name

Popular brands