manualshive.com logo in svg

Clarke PRO-MIST DURA, Instruction Manual And Parts List, Page: 92 / 133

Share
Download
Clarke PRO-MIST DURA Instruction Manual And Parts List Download Page 92

89

SMARTFLOW II

Calibration Factors Overview

The SmartFlow II control has 8 calibration factors:

CALIBRATION FACTOR

ROTARY SWITCH POSITION DESCRIPTION

Alarm Setting

AREA (1) (2) (3)

Sets the delay time for triggering the audible alarm.

Speed Cal

DISTANCE

Specifies the distance the vehicle travels between 
speed sensor pulses. This enables the SmartFlow II 
control to accurately measure speed, distance, area 
and application rate. 

Cont. Speed

TIME

The speed that is used in Continuous mode.

Test Speed

SPEED

Not a  true calibrate factor, but a method of testing  
the sprayer.

Target Rate

RATE

Sets the three preset Target Application Rates.

Min Speed

MIN SPEED

The minimum speed allowed in Variable mode. If the  
vehicle goes below this speed, the control goes into  
Off mode until the speed exceeds this number again.

Max Speed

VOLUME/MINUTE

The maximum speed allowed in Variable mode. If the  
vehicle exceeds this speed the control goes into OFF 
mode until the speed goes below this number again.

Flow Cal

FLOW CAL

Specifies the number of flow sensor pulses per gallon  
applied. This enables the Smart Flow control to  
accurately measure total flow, flow per minute,  
and application rate.

CALIBRATION

Summary of Contents for PRO-MIST DURA






































































































































Reviews:

No comments