manualshive.com logo in svg

Clarke PRO-MIST DURA, Instruction Manual And Parts List, Page: 90 / 133

Share
Download
Clarke PRO-MIST DURA Instruction Manual And Parts List Download Page 90

87

SMARTFLOW II

Push Buttons

2. INC (+) and   
3. DEC (-)

The 

INC/DEC

 buttons are used to enter or adjust values 

in the display.

If in Volume or Area mode the 

INC/DEC

 buttons will 

select 1 of 3 counters.

If in the 

Tank

 mode then the 

INC

 or 

DEC

 buttons are 

used to change the Tank level. This also works while  
in the PCCC (PC Command/Control) mode.

If in 

Speed

 

position and 

Test Speed

 

mode, then the 

INC 

and 

DEC 

buttons will adjust the Test Speed.

In the 

Calibrate

 or special 

Calibrate Mode

, the 

INC

  

or 

DEC

 buttons are pressed to increase or decrease  

each Calibrate value and the longer the key is pressed 
the faster the value will change. (See Maintenance Alert  
section for additional use of the 

DEC

 button).

4. CAL Button

Used to start and stop the Calibrate modes (see  
Calibrate Modes and Special Calibrate Modes).

+

-

CAL

CONTROL PANEL FUNCTIONS

Summary of Contents for PRO-MIST DURA






































































































































Reviews:

No comments