Cisco DPA 7610 Administration Manual Download Page 26 | Manualshive

Page: 26 / 188

background image

Chapter 1

Overview

Understanding the DPA 7630/7610

1-2

Cisco DPA 7630/7610 Voice Mail Gateways Administration Guide

78-11069-03

Understanding the DPA 7630/7610

The Cisco DPA 7630/7610 enables you to integrate your existing Octel voice mail
with Cisco CallManager and either a Definity PBX system or a Meridian 1 PBX
system. If you have a Definity PBX, use the DPA 7630; if you have a Meridian 1
system, use the DPA 7610.

The DPA 7630/7610 functions as a gateway between the Octel, PBX systems, and
Cisco CallManager, performing these tasks:

•

Determines the call type from Cisco CallManager and sends envelope
(display), light, and ring messages to the Octel system.

•

Determines when the Octel system is attempting to transfer, outcall, set
message waiting indicators (MWI) and so on, and sends the appropriate
messages to Cisco CallManager.

•

Converts Dual-Tone Multi-Frequency (DTMF) tones to Skinny Client
Control Protocol (SCCP) messages.

•

Converts Nortel Display Key commands to Skinny Client Control Protocol
(SCCP) messages

•

Provides companding-law transcoding, and voice compression.

•

Performs Real-Time Transport (RTP) encapsulation of the voice message.

These sections provide additional detail about the interfaces and supported
protocols on the DPA 7630/7610:

•

DPA 7630/7610 Physical Description, page 1-2

•

Supported Protocols on the DPA 7630/7610, page 1-6

DPA 7630/7610 Physical Description

The DPA 7630/7610 is a 19-inch, rack-mountable hardware device capable of
emulating digital telephones or digital PBX ports. By emulating these devices, the
DPA 7630/7610 enables you to integrate Cisco CallManager with existing Octel
voice mail systems and Definity or Meridian 1 PBX systems.

The wiring and external connectors of the DPA 7630 and the DPA 7610 differ
slightly because the Definity system uses a 4-wire wiring scheme, and the
Meridian 1 system uses a 2-wire wiring scheme.

«
...
24
25
26
27
28
...
»

Summary of Contents for DPA 7610





























































































































































































Reviews:

No comments

Related manuals for DPA 7610

Brand: Sangoma Pages: 2

Brand: Farfisa Pages: 12

Brand: Verizon Pages: 3

Brand: Wiznet Pages: 41

Brand: SIEB & MEYER Pages: 40

Brand: Mako Pages: 70

1898921 RSL 433 MHz

Brand: Sygonix Pages: 45

PVSG-IQAN-C2E1M2W1U1

Brand: Parker Pages: 70

Brand: Sunfull Pages: 2

Brand: Bticino Pages: 4

Brand: NextCentury Pages: 4

Brand: eQ-3 Pages: 44

Brand: Dr. Neuhaus Pages: 2

Brand: Maverick Pages: 21

Brand: Exegin Pages: 84

Brand: Cooper Bussmann Pages: 115

Brand: Black Box Pages: 110

Brand: DEERE Pages: 45

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands