Cisco DPA 7610 Administration Manual Download Page 104

Page: 104 / 188

Chapter 5

Getting Started with the DPA 7630/7610

Configuring Network Settings

5-12

Cisco DPA 7630/7610 Voice Mail Gateways Administration Guide

78-11069-03

Assigning the NTP Server

If you choose to use an NTP server to synchronize the time settings on the
DPA 7630/7610 (see

“Identifying the Time Source for Event Logs” section on

page 5-10

), you must assign an NTP server and designate its time zone.

To set the NTP server, perform these steps:

Step 1

From the main menu, choose Configure.

Step 2

Choose Network interface.

Step 3

Choose NTP server.

Step 4

Enter the IP address of the NTP server.

Note

If you are using DHCP to obtain an IP address on the DPA 7630/7610, the
DHCP server should also indicate the NTP server.

Step 5

Restart the DPA 7630/7610.

Enabling CDP

The DPA 7630/7610 can advertise itself to other network devices using
Cisco Discovery Protocol (CDP). Many network management applications
require that CDP is enabled.

To enable CDP, perform these steps:

Step 1

From the main menu, choose Configure.

Step 2

Choose Network interface.

Step 3

Choose CDP.

Step 4

Press Enter to toggle between enabled and disabled.

Step 5

Restart the DPA 7630/7610.

Summary of Contents for DPA 7610





























































































































































































Search results

Summary of Contents for DPA 7610

Reviews:

Related manuals for DPA 7610

Brands by name

Popular brands

Cisco DPA 7610, Administration Manual

Search results

Summary of Contents for DPA 7610

Reviews:

Related manuals for DPA 7610

Brands by name

Popular brands