Cisco DPA 7610 Administration Manual Download Page 132

Page: 132 / 188

Chapter 7

Troubleshooting the DPA 7630/7610

Displaying Status and Configuration Settings

7-10

Cisco DPA 7630/7610 Voice Mail Gateways Administration Guide

78-11069-03

To display port status, perform these steps:

Step 1

From the main screen, choose Display.

Step 2

Choose Port status.

Step 3

Use the information in

Table 7-3

and

Table 7-4

to interpret the port status.

Table 7-3

Types of Ports

Type

Description

Call

This port is used for general call processing.

Oct MWI

This port is used to receive MWI commands from the Octel
system.

PBX MWI

This port is used to set MWI commands on the Definity or
Meridian 1 PBX systems.

Virtual

This “port” is an IP phone used for setting MWI commands on
Cisco CallManager.

Down

The link to the Octel or PBX port is not connected. Unused
ports display as “down.”

Table 7-4

Port Status

Status

Description

Used By Port
Type

DPA 7630/7610

Octel registering

This indicates an intermediate state when
the DPA 7630/7610 is starting up a port’s
connection to the Octel system.

•

Call

•

Oct MWI

DPA 7630/7610

Octel link down

The port previously had a connection to
the Octel system, but the connection is
down.

•

Call

•

Oct MWI

DPA 7630/7610

CM link registering This indicates an intermediate state when

the DPA 7630/7610 is registering an IP
phone with Cisco CallManager.

•

Call

•

Oct MWI

•

Virtual

DPA 7630/7610

Summary of Contents for DPA 7610





























































































































































































Search results

Summary of Contents for DPA 7610

Reviews:

Related manuals for DPA 7610

Brands by name

Popular brands

Cisco DPA 7610, Administration Manual

Search results

Summary of Contents for DPA 7610

Reviews:

Related manuals for DPA 7610

Brands by name

Popular brands