Cisco DPA 7610 Administration Manual Download Page 125 | Manualshive

Page: 125 / 188

background image

7-3

Cisco DPA 7630/7610 Voice Mail Gateways Administration Guide

78-11069-03

Chapter 7

Troubleshooting the DPA 7630/7610

Upgrading Software Images

Upgrading the Boot Loader

The boot loader is the initial startup image. You should not upgrade this image
unless instructed by a Cisco technical representative.

Caution

Only upgrade the boot loader if you are instructed to do so by a Cisco technical
representative. If you encounter difficulties during this upgrade, such as a loss of
power, the DPA 7630/7610 might not be able to start up.

To upgrade the boot loader image, perform these steps:

Step 1

Obtain a configuration file whose name is in the following format:

dpa-loader.

<version>

.bin

, where <version> indicates the release number, such

as 1-1-2.

Step 2

Ensure the DPA 7630/7610 has started up normally.

Step 3

Connect to the DPA 7630/7610 using FTP and send the configuration file to it.

Step 4

While still connected to the DPA 7630/7610 using FTP, enter a

dir

command to

verify that the new file is on the DPA 7630/7610.

Step 5

On the DPA, choose Diagnostics from the main menu.

Step 6

Choose Reprogram boot ROM.

Caution

If the DPA 7630/7610 loses power or experiences a failure at this step, the
DPA 7630/7610 might not start up. If this occurs, contact a Cisco technical
representative for assistance.

Step 7

Choose Yes to confirm.

The Boot ROM reprogrammed message appears verifying the programming has
finished.

Step 8

Restart the DPA 7630/7610 for the changes to take effect.

«
...
123
124
125
126
127
...
»

Summary of Contents for DPA 7610





























































































































































































Reviews:

No comments

Related manuals for DPA 7610

Brand: C-Bus Pages: 36

Modular IoT Gateway

Brand: Volansys Pages: 26

Brand: ATCOM Pages: 8

Brand: Badger Meter Pages: 24

Brand: NETGEAR Pages: 10

Brand: 2N Pages: 113

SIMATIC IOT2020

Brand: Siemens Pages: 2

SIMATIC IOT Gateway MQTT

Brand: Siemens Pages: 2

MindConnect Nano

Brand: Siemens Pages: 2

Instabus/DALI Gateway N 141

Brand: Siemens Pages: 5

SIMATIC IOT2050

Brand: Siemens Pages: 25

GAMMA 5WG1 143-1AB01

Brand: Siemens Pages: 2

Brand: Siemens Pages: 6

Brand: Siemens Pages: 8

Brand: Siemens Pages: 20

SIMATIC PN/M-Bus LINK

Brand: Siemens Pages: 62

Brand: Siemens Pages: 43

Brand: Siemens Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands