manualshive.com logo in svg

Cisco ASR 903, Release Notes, Page: 65 / 280

Share
Download
Cisco ASR 903 Release Notes Download Page 65

 

13

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-08

Chapter Restrictions and Caveats in Cisco IOS XE 3.6S Releases

  Caveats in Cisco IOS XE 3.6S Releases

Workaround:

 There is no workaround. 

Resolved Caveats—Cisco IOS XE Release 3.6(1)S

This section documents the issues that have been resolved in Cisco IOS XE Release 3.6S(1).

•

CSCtu35052

Symptoms:

 Sweep ping fails when an ATM interface is configured with AAL5 encapsulation. 

Conditions:

 Occurs when the ATM packet size is greater than 1484 bytes. 

Workaround:

 There is no workaround. 

•

CSCtw94068

Symptoms:

 The router displays traceback messages, after which interfaces stop passing traffic. 

Conditions:

 The issue can occur when you reload the router 

Workaround:

 There is no workaround. 

•

CSCtx37768

Symptoms:

 QoS classification does not match traffic against an egress policy map between MPLS 

and IP access. 

Conditions:

 This symptom is observed when a QoS policy is applied on an EVC bridge domain 

interface. 

Workaround:

 Use one of the following workarounds: 

–

Reload the router. 

–

Remove and re-apply an encapsulation configuration such a VLAN. 

–

Remove and re-attach the bridge domain under the EVC. 

–

Perform a shutdown/no shutdown on the BDI interface. 

•

CSCtx73691

Symptoms:

 The ASR 903 router forwards packets while in HSRP standby mode. 

Conditions:

 Occurs when the ASR 903 is running HSRP and the HSRP session flaps. 

Workaround:

 There is no workaround. 

•

CSCtx87145

Symptoms:

 The ASR 903 router does not support LDP label packets when transmitted in PTP 

delay-request messages.

Conditions:

 Occurs when you configure the ASR 903 router as a PTP (1588 version) boundary 

clock and the router sends an MPLS label packet within delay-request traffic.

Workaround:

 Align the grandmaster clock source to the same IGP domain and use a prefix-list for 

local label filtering. 

•

CSCty03480

Symptoms:

 The interface manager crashes when you remove a BFD template. 

Conditions:

 Occurs when you remove a BFD template or modify an MPLS-TP label. 

Workaround:

 There is no workaround. 

•

CSCty03617

Summary of Contents for ASR 903

























































































































































































































































































Reviews:

No comments