manualshive.com logo in svg

Cisco ASR 903, Release Notes, Page: 176 / 280

Share
Download
Cisco ASR 903 Release Notes Download Page 176

 

34

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-08

Chapter

  Caveats in Cisco IOS XE 3.8S Releases

Conditions:

 Upgrade to the new firmware rev. and a subsequent switchover. Occurs when you 

upgrade the router to a new firmware version and issue an RSP switchover.

Workaround:

 Reloading the RSP can resolve the issue.

•

CSCud60410

Symptom:

 The router drops EFP traffic.

Conditions:

 Occurs when you add a new EFP to an existing bridge domain interface (BDI) while 

running L3 multicast.

Workaround:

 Issue a 

shutdown

/

no shutdown

 on the Ethernet interface and issue the 

clear ip 

mroute

 command.

•

CSCud61931

Symptom: 

As OC-3 interface module controller does not become active using loopback local.

Conditions: 

Occurs with the A900-IMA4OS interface module when there is no SFP inserted in the 

port.

Workaround: 

Insert an SFP in the appropriate port.

•

CSCud64347

Symptom: 

The router creates a data loop when using a REP VLAN load balancing configuration.

Conditions:

 Occurs with a REP VLAN load balancing configuration when a bridge-domain is 

bound to a VPLS VC.

Workaround: 

None; remove the VLAN load balancing configuration.

•

CSCud64923

Symptom:

 OSPF connections flap.

Conditions:

 Occurs when you configure OSPF between an EVC bridge domain interface (BDI) and 

a trunk EFP bridge domain interface (BDI) using a port-channel trunk.

Workaround:

 There is no workaround.

•

CSCud65779

Symptom:

 The router does not update the Rx value for C2, J1, and S1S0 bytes.

Conditions:

 Occurs when you configure overhead bytes on OC-3 connections.

Workaround:

 There is no workaround.

•

CSCud65935

Symptom:

 End to end ATM ping does not work.

Conditions:

 Occurs when you configure a different set of VPI/VCI on either end of an ATM layer 

2 circuit.

Workaround:

 Configure the same VPI/VCI values on both sides of the connection.

•

CSCud71546

Symptom: 

The ten Gigabit Ethernet interface drops traffic for 7 seconds following a stateful 

switchover (SSO).

Conditions:

 Occurs when the configuration contains static routes to the destination.

Workaround:

 There is no workaround.

•

CSCud76209

Symptom:

 The OC-3 interface module goes into an out of service state.

Summary of Contents for ASR 903

























































































































































































































































































Reviews:

No comments