manualshive.com logo in svg

Cisco ASR 903, Release Notes, Page: 47 / 280

Share
Download
Cisco ASR 903 Release Notes Download Page 47

 

7

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-08

Chapter

  New Software Features in Cisco IOS XE Release 3.10S

Note

We recommend the installation of the Metro IP Services and Metro Aggregation Services licenses with 
serial interface module. For more information about obtaining and installing licenses, see 

Software 

Licensing Overview

.

Hardware Limitations

Serial Interface Module Limitations—The following limitations apply to the serial interface module:

•

A maximum of 2 serial interface modules are supported on the Cisco ASR 903 Router.

•

The serial interface module hardware supports a 230.4 Kbps traffic rate in asynchronous mode. The 
actual speed is dependent on cable quality and length. The serial interface module hardware supports 
an 8 Mbps traffic rate in synchronous mode. The actual speed is dependent on cable quality and 
length.

Software Limitations

Raw Socket limitations—The following software limitations apply to the serial interface module:

•

Raw Socket encapsulation is supported on up to 28 serial ports.

•

Asynchronous EIA/TIA-232 serial traffic is supported with DB-25, DB-9, and RJ-45 connectors. 

•

The X.21, V.35, RS-485, EIA-449, EIA-530, and IRIG-B standards are not currently supported by 
software.

•

Synchronous traffic is not currently supported.

Remote LFA FRR Protection for TDM and ATM Pseudowires

Starting with Cisco IOS XE Release 3.10S, the Loop-Free Alternate (LFA) Fast Reroute (FRR) feature 
is supported for Time-division multiplexing (TDM) pseudowires.

•

Circuit Emulation Service over Packet Switched Network (CESoPSN) over MPLS, and 
Structure-Agnostic Time Division Multiplexing over Packet (SAToP) over MPLS networks for T1, 
E1, SDH and SONET framing is supported.

•

Inverse Multiplexing over ATM (IMA) over MPLS; PVC and PVC sessions are supported for the 
ATM (IMA).

For more information see,

 Configuring Loop-Free Alternate Fast Reroute on the Cisco ASR 903 Router

.

Remote LFA FRR and Labeled BGP PIC FRR Integration

Starting with Cisco IOS XE Release 3.10S, Both the Labeled Border Gateway Protocol (BGP) 
Prefix-Independent Convergence (PIC) feature and the Loop-Free Alternate (LFA) Fast Reroute (FRR) 
feature can be configured together on the Cisco ASR 903 router.

For more information see,

 Configuring Loop-Free Alternate Fast Reroute on the Cisco ASR 903 Router

.

Summary of Contents for ASR 903

























































































































































































































































































Reviews:

No comments