manualshive.com logo in svg

Cisco ASR 903, Release Notes, Page: 38 / 280

Share
Download
Cisco ASR 903 Release Notes Download Page 38

 

4

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-08

Chapter New Features in Cisco IOS XE 3.9S Releases

  New Software Features in Cisco IOS XE Release 3.9(0)S

•

L2VPN Protocol Support—This release introduces support for additional L2VPN protocols 
including L2TP and UDP. For more information, see 

http://www.cisco.com/en/US/docs/ios-xml/ios/mp_l2_vpns/configuration/xe-3s/l2vpn-prot-based.
html

•

Microwave Adaptive Bandwidth Modulation Enhancement—This release introduces support for 
Adaptive Bandwidth Modulation on G.8032 and E-OAM microwave connections, which allow 
Ethernet switches to optimize traffic forwarding rules based on microwave link capacity. For more 
information, see

–

http://www.cisco.com/en/US/docs/routers/asr903/feature/guide/mw_acm.html

–

http://www.cisco.com/en/US/docs/ios-xml/ios/cether/configuration/xe-3s/asr903/ce-cfm-adapt-b
andwidth.html.

•

MPLS on MLPPP Interfaces—This release introduces support for MPLS on MLPPP interfaces. For 
more information about configuring MPLS, see the 

MPLS Basic MPLS Configuration Guide, Cisco 

IOS XE Release 3S (Cisco ASR 903)

. For more information about configuring MLPPP interfaces, 

see 

http://www.cisco.com/en/US/docs/routers/asr903/software/guide/chassis/Release3.9.0S/ASR903-
Chassis-SW-39.html

.

•

MPLS -TP Linear Protection/PSC support—Linear Protection on MPLS-TP based transport 
networks using the RFC 6378 standard. For more information, see 

http://www.cisco.com/en/US/docs/ios-xml/ios/mp_basic/configuration/xe-3s/asr903/mp-basic-xe-
3s-asr903-book.html.

•

MVPN—The Multicast VPN (MVPN) feature provides the ability to support multicast over a Layer 
3 Virtual Private Network (VPN). For more information, see 

http://www.cisco.com/en/US/docs/ios-xml/ios/ipmulti_mvpn/configuration/xe-3s/asr903/imc_cfg_
mc_vpn.html.

•

On-Demand Y.1731PM Probe Execution—This release introduces support for IPSLA Y1731 SLM 
enhancements that enable real-time Ethernet service troubleshooting for users without configuration 
privileges. This feature supports on-demand Synthetic Loss Measurement (SLM) operations that can 
be run by issuing a single command in privileged EXEC mode. For more information, see 

http://www.cisco.com/en/US/docs/ios-xml/ios/ipsla/configuration/xe-3s/sla_y1731_demand.html

•

OC-12 HDLC, PPP, and MLPPP support—This release introduces support for HDLC, PPP, and 
MLPPP on OC-12 interfaces. For more information, see 

http://www.cisco.com/en/US/docs/routers/asr903/software/guide/chassis/Release3.9.0S/ASR903-
Chassis-SW-39.html

.

•

POS (Packet over SONET/SDH) on OC12 IM card—This release introduces support for Packet over 
SONET (POS) and SDH on OC-12 interfaces. For more information, see 

http://www.cisco.com/en/US/docs/routers/asr903/software/guide/chassis/Release3.9.0S/ASR903-
Chassis-SW-39.html

•

PTP over Native Ethernet—This release introduces support for IEEE 1588-2008 Precision Time 
Protocol (PTP) on native Ethernet interfaces; this allows the router to deliver the PTP payload within 
an Ethernet packet. For more information, see 

http://www.cisco.com/en/US/docs/routers/asr903/software/guide/chassis/Release3.9.0S/ASR903-
Chassis-SW-39.html

.

•

QoS Ingress Exp Bit Marking—This release introduces support for ingress QoS marking of MPLS 
Exp bits on TDM and ATM pseudowires. For more information, see 

http://www.cisco.com/en/US/docs/routers/asr903/software/guide/chassis/Release3.9.0S/ASR903-
Chassis-SW-39.html

.

Summary of Contents for ASR 903

























































































































































































































































































Reviews:

No comments