manualshive.com logo in svg

Cisco ASR 903, Release Notes, Page: 159 / 280

Share
Download
Cisco ASR 903 Release Notes Download Page 159

 

17

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-08

Chapter

  Caveats in Cisco IOS XE 3.8S Releases

•

CSCue27652

Symptom:

 ATM interfaces get deleted after SSO is performed.

Conditions:

 This issue occurs after an the ATM interfaces are deleted on the standby RSP after an 

IM OIR is performed.

Workaround:

 There is no workaround. 

•

CSCue30481

Symptom:

 The router does not lock to the syncE clock source after reload. It will be in Ql-failed 

state.

Condition:

 Reload the router with saved syncE configuration.

Workaround:

 Unconfigure and configure the clock source.

•

CSCue32753

Symptom:

 The OC-3 interface modules are lost after a In Service Software Upgrade (ISSU) is 

performed on the Cisco ASR 903 router and configuration mismatch errors are displayed on router 
console. The standby RSP reaches standby-hot state causing continuous IOMD crash messages at 
regular intervals.

Conditions:

 This issue occurs when ISSU is performed.

Workaround:

 There is no workaround. 

•

CSCue34597

Symptom:

 CHAP authentication process timed out. The PPP interface and multilink bundle does 

not come up.

Conditions:

 This issue occurs when PPP or MLPPP is configured and PPP authentication is 

enabled.

Workaround:

 Remove CHAP authentication from interface.

•

CSCue40020

Symptom:

 Interior Gateway Protocol (IGP) flap or MPLS-enabled interface flap with 600 Layer2 

VPN configured and 6000 Layer3 VPN configured can cause a crash.

Conditions:

 This issue occurs after the IGP flaps continuously.

Workaround:

 Configure IGP routes less than 100. Scale of Layer2 or Layer3 VPN configuration 

should be less than 100 to avoid a crash.

•

CSCue42315

Symptom:

 CPU hog messages and IOMD crash observed on the Cisco ASR 903 router.

Conditions:

 This issue occurs with OC-3 interface module after executing the shutdown command 

followed by a no shutdown command of the multilink bundle when traffic is sent with a packet size 
greater then 1500 byte.

Workaround:

 There is no workaround.

•

CSCue43250

Symptom:

 IMA configurations cannot be parsed correctly after a router reload.

Conditions:

 This issue occurs after the A903-IM40S is inserted in bay 4 or bay 5 of the Cisco 

ASR903 router and when the IMA and ATM interfaces are adjacent. 

Workaround:

 Insert the IM in bay 0 or bay 3 for the IMA and ATM parsing to work or reconfigure 

the ATM and IMA interfaces.

Summary of Contents for ASR 903

























































































































































































































































































Reviews:

No comments