manualshive.com logo in svg

Cisco ASR 903, Release Notes, Page: 44 / 280

Share
Download
Cisco ASR 903 Release Notes Download Page 44

 

4

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-08

Chapter

  New Software Features in Cisco IOS XE Release 3.10S

•

Auto-IP, page 6-4

•

BFD Debug Enhancement, page 6-4

•

Bidirectional Forwarding Detection Deterministic Hardware Offload, page 6-5

•

Broadcast and Multicast Suppression, page 6-5

•

IGMP Snooping, page 6-5

•

Licensing the OC-3 and OC-12 Interface Modules, page 6-5

•

Multichassis LACP, page 6-6

•

Pseudowire Group Switchover, page 6-6

•

Remote LFA FRR Protection for TDM and ATM Pseudowires, page 6-7

•

Remote LFA FRR and Labeled BGP PIC FRR Integration, page 6-7

•

VPLS over Remote LFA, page 6-8

Access Circuit Redundancy

Access Circuit Redundancy (ACR) enables local switching for circuit emulation (CEM) interfaces by 
creating a virtual CEM-ACR interface. All configuration changes made on the virtual CEM-ACR 
interface are applied automatically on both the Working and Protect interfaces.

For more information see, 

Configuring Access Circuit Redundancy on the Cisco ASR 903 Router

.

Access Switch Device Manager Template

The Switch Device Manager (SDM) templates are used to optimize system resources in the router to 
support specific features, depending on how the router is used in the network. The SDM templates 
allocate Ternary Content Addressable Memory (TCAM) resources to support different features.

Note

SDM templates are supported only by the Metro Aggregation Services license.

For more information see, 

Configuring Access Switch Device Manager Template on the Cisco ASR 903 

Router.

Auto-IP

The Auto-IP feature addresses the problem of manually reconfiguring nodes during insertion, deletion, 
and movement of nodes within an auto-IP ring. The auto-IP feature automatically provides IP addresses 
to the node interfaces inserted into an auto-IP ring.

For more information, see

 Auto-IP

.

BFD Debug Enhancement

The Bidirectional Forwarding Detection (BFD) Debug Enhancement feature enhances the BFD debug 
messages and the show command output and enables logs and history for critical BFD events. This 
feature helps network engineers and operators to easily identify any issues with BFD sessions or events. 

The following commands were introduced for this feature: monitor event-trace bfd, monitor event-trace 
bfd event, monitor event-trace bfd packet, and show monitor event-trace bfd.

Summary of Contents for ASR 903

























































































































































































































































































Reviews:

No comments