manualshive.com logo in svg

Cisco ASR 903, Release Notes, Page: 229 / 280

Share
Download
Cisco ASR 903 Release Notes Download Page 229

 

43

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-08

  Caveats in Cisco IOS XE 3.9S Releases

•

CSCud07085

Symptom:

 The serial interface on the OC-3 interface module remains in a down state.

Conditions:

 Occurs when you migrate from T1 mode to E1 mode using the OC-3 interface module.

Workaround:

 Issue an interface module reset (OIR) on the OC-3 interface module.

•

CSCud07236

Symptoms:

 Upon reload few harmless messages will seen. 

Conditions:

 Upon reload few harmless messages will seen. 

Workaround:

 No impact on device. 

•

CSCud07642

Symptom:

 The ASR 903 is unable to pass traffic to the ASR 9000. 

Conditions:

 Occurs with a clear-channel ATM over MPLS configuration using AAL0 

encapsulation. 

Workaround:

 Enable MPLS control-word on the ASR 9000.

•

CSCud09813

Symptoms: 

Timestamping not happening in CFM over xconnect down mep/PC

Conditions: 

When we configured cfm over xconnect down mep/PC from Asr903-Me3600 

timestamping not happening in ASR903.

Workaround: 

No workaround.

•

CSCud22601

Symptom:

 MPLS-TP tunnels remain down after the standby RSP boots.

Conditions:

 Occurs when you boot the standby RSP after applying an MPLS-TP configuration and 

performing an SSO. The issue occurs rarely.

Workaround:

 Issue a shutdown/no shutdown on the MPLS-TP tunnel. A nonintrusive workaround 

is to cause a flap on the protect label switched path (LSP) by reconfiguring the path or physically 
shutting down and restoring the interface. 

•

CSCud23647

Symptom: 

BDI adjacency fails on the standby RSP.

Conditions: 

The issue can occur during an interface module (IM) reset or router reload.

Workaround: 

There is no workaround.

•

CSCud25764

Symptoms:

 903 part id to be populated in the discovery messages.

Conditions:

 Currently it is being displayed as "cisco, asr903" against Vendor in host by executing 

this CLI "show nv satellite protocol discovery interface Bundle-Ether1000". This must be displayed 
as cisco, ASR-903. This is mainly used by ASR9K ACT tool for rendering 903 graphic on Act tool.

Workaround:

 No workaround. 

•

CSCud26812

Symptom:

 The router CLI does not display some SFP PIDs

Conditions:

 Occurs when you install one of the following SFPs in the router:

–

ONS-SI-155-L2

–

ONS-SI-155-L1

Summary of Contents for ASR 903

























































































































































































































































































Reviews:

No comments