manualshive.com logo in svg

Cisco ASR 903, Release Notes, Page: 113 / 280

Share
Download
Cisco ASR 903 Release Notes Download Page 113

 

31

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-08

Chapter

  Caveats in Cisco IOS XE 3.7S Releases

•

CSCue16617

Symptom:

 The QoS classification does not work in core interfaces.

Conditions:

 This issue occurs when the output policy applied to interface has bridge domain 

interface (BDI) as the core interface.

Workaround:

 Enable 

mpls ldp explicit null

 command.

•

CSCue18015

Symptom:

 S,G does not get created, the forwarding is based on (*,G).

Conditions:

 This issue occurs with Interior Gateway Protocol (IGP) change leading to Reverse Path 

Forwarding (RPF) change of the (*,G).

Workaround:

 Clear the (*,G) and recreate it.

•

CSCue19898

Symptom:

 (*,G) based forwarding is observed with IIF registry change. The Interior Gateway 

Protocol (IGP) patch change leads to this issue.

Conditions:

 This issue occurs when IGP is changed causing a Reverse Path Forwarding (RFP) 

change notification.

Workaround:

 Timeout the (*,G) entry and recreate it again either by issuing 

clear ip mroute

 

command or stopping the joins.

•

CSCue20022

Symptom:

 Software forwarding of core encapsulation entries causes interface to flap.

Conditions: 

This issue occurs when interface has Protocol Independent Multicast (PIM) enabled on 

the BDI interface.

Workaround:

 Perform a soft interface module OIR. Clear the multicast routes for that VRF.

•

CSCue20360

Symptom: 

The router does not learn the remote Connectivity Fault Management (CFM) 

Maintenance Endpoint (MEPs).

Conditions: 

This issue occurs when Resilient Ethernet Protocol (REP) or Spanning Tree Protocol 

(STP) exists on core with one port as ALT or BLK state.

Workaround:

 There is no workaround.

•

CSCue20607

Symptom:

 The port-channel load balances the traffic on member-links in hot-standby state or down 

state resulting in loss of traffic.

Conditions:

 This issue occurs when there are redundant member-links in hot-standby state or down 

state.

Workaround:

 There is no workaround.

•

CSCue25567

Symptom: 

Quack authentication failure messages are displayed on router console.

Conditions:

 This issue occurs randomly.

Workaround: 

Reload the router.

Summary of Contents for ASR 903

























































































































































































































































































Reviews:

No comments