manualshive.com logo in svg

Cisco ASR 903, Release Notes, Page: 247 / 280

Share
Download
Cisco ASR 903 Release Notes Download Page 247

 

5

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-08

Chapter

  Caveats in Cisco IOS XE 3.10S Releases

Conditions: This issue occurs while shutting down he gigabit ethernet interface.

Workaround: There is no workaround.

•

CSCuj51830

Symptom: Traffic drops if policy is attached on port-channel interface.

Conditions: This issue occurs when the policy is attached on port-channel interface

Workaround: Use port-channel IDs less than 10.

•

CSCuj56164

 Symptom: TCAM utilization shows incorrect current usage percentage.

 Conditions: This issue occurs when EQoS application is enabled.

 Workaround: There is no workaround.

Resolved Caveats—Cisco IOS XE Release 3.10.1S

This section documents the issues that have been resolved in Cisco IOS XE Release 3.10.1S.

•

CSCue60699

Symptom:

 Router auto negotiates full duplex with 1000M half/full duplex configuration.

Conditions:

 This issue occurs when a router with Copper SFP with auto-negotiating is enabled and 

the peer router with Cu SFP configured with 1000M half-duplex mode exists.

Workaround:

 There is no workaround.

•

CSCug31550

Symptom:

 Incorrect TCAM entries with scale configuration are displayed after reapplying the 

policy map.

Conditions:

 This issue occurs after removing the policy map and reapplying it to service instances.

Workaround:

 There is no workaround.

•

CSCug36190

Symptom:

 Object Download failures are seen when configuring xconnect on the main interface and 

configure xconnect under the service instance.

Conditions:

 This issue occurs when xconnect is configured on the main interface. 

Workaround

: Remove the xonnect configuration from the main interface.

•

CSCug50280

Symptom:

 QoS does not work on the router.

Conditions:

 This issue occurs while adding user class to a port level policer dynamically when the 

policer already has class-default configured.

Workaround:

 Reload the router.

•

CSCug68820

Symptom:

 The 

show inventory

 command does not display PSU and fan tray information.

Conditions:

 This issue occurs after the PSU or fan tray is inserted after bootup and SSO is 

performed.

Workaround:

 Reload after PSU or the fan tray after it is inserted.

Summary of Contents for ASR 903

























































































































































































































































































Reviews:

No comments