manualshive.com logo in svg

Cisco ASR 903, Release Notes, Page: 158 / 280

Share
Download
Cisco ASR 903 Release Notes Download Page 158

 

16

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-08

Chapter

  Caveats in Cisco IOS XE 3.8S Releases

Symptom:

 Back-to-Back ping failure observed on a PC with Core side Trunk EFP with BDI 

configured.

Conditions:

 This issue occurs when a PC with Core side Trunk EFP with BDI configuration is 

changed.

Workaround: Do not change the PC in Core side.

•

CSCue18015

Symptom:

 S,G does not get created, the forwarding is based on (*,G).

Conditions:

 This issue occurs with Interior Gateway Protocol (IGP) change leading to Reverse Path 

Forwarding (RPF) change of the (*,G).

Workaround:

 Clear the (*,G) and recreate it. 

•

CSCue19898

Symptom:

 (*,G) based forwarding is observed with IIF registry change. The Interior Gateway 

Protocol (IGP) patch change leads to this issue.

Conditions:

 This issue occurs when IGP is changed causing a Reverse Path Forwarding (RFP) 

change notification.

Workaround:

 Timeout the (*,G) entry and recreate it again either by issuing 

clear ip mroute

 

command or stopping the joins.

•

CSCue20022

Symptom:

 Software forwarding of core encapsulation entries causes interface to flap.

Conditions:

 This issue occurs when interface has Protocol Independent Multicast (PIM) enabled on 

the BDI interface.

Workaround:

 Perform a soft interface module OIR. Clear the multicast routes for that VRF.

•

CSCue25146

Symptom: 

The standby OC-3 IM gets reloaded after the controller flaps in active console.

Conditions:

 This issue occurs after configuring ATM and Controller and a 

shutdown

 command 

followed by a 

no shutdown

 command is issued when the controller in active.

Workaround: 

There is no workaround.

•

CSCue25267

Symptom:

 The standby RSP reloads on an OC-3 interface module OIR on the active RSP. A crash 

was observed but core file generated is incomplete.

Conditions:

 This issue occurs when the active RSP is booted up first followed by the standby RSP. 

This issue occurs when APS configurations with serial links are present on the router and IM OIR 
is performed.

Workaround:

 There is no workaround.

•

CSCue25567

Symptom: 

Quack authentication failure message seen on console.

Conditions:

 This issue is seen randomly.

Workaround:

 Reload the router. 

Summary of Contents for ASR 903

























































































































































































































































































Reviews:

No comments