manualshive.com logo in svg

Cisco ASR 903, Release Notes, Page: 249 / 280

Share
Download
Cisco ASR 903 Release Notes Download Page 249

 

7

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-08

Chapter

  Caveats in Cisco IOS XE 3.10S Releases

•

CSCuh51651

Symptom:

 CPP download failures and CFM remote MEPS not learnt.

Conditions:

 This issue occurs during configuring CFM offload scaled configurations using TFTP.

Workaround:

 There is no workaround.

•

CSCuh51702

Symptom:

 The system shuts down after 5mins irrespective of ambient temperature after removing 

the fan tray.

Conditions:

 This issue occurs after removing the fan tray.

Workaround:

 There is no workaround.

•

CSCuh81135

Symptom:

 Port speed configuration is changed automatically on changing the SFP module.

Conditions:

 This issue occurs on changing the SFP module.

Workaround:

 There is no workaround.

•

CSCuh85990

Symptom:

 Some CFM MEPs are not learnt when configuring large number (about 1K) on the router.

Conditions:

 This issue is seen only if large number of MEPs are configured. 

Workaround:

 Remove and re-apply the configuration. 

•

CSCuh92939

Symptom:

 Traffic drop occurs after replacing a Cu SFP with a fiber FP 

Conditions:

 This issue occurs after replacing Cu SFP with fiber SFP after an SSO is performed.

Workaround:

 Perform an IM OIR.

•

CSCuh99117

Symptom:

 Packet drops for some of the prefixes in MPLS network are observed.

Conditions:

 This issue occurs when MPLS Layer3 VPN is configured on the router with MVPN 

template.

Workaround:

 There is no workaround.

•

CSCui16418

Symptom

: After a switchover is performed, the ten gigabit ethernet interface might flap and traffic 

drops. 

Conditions:

 This issue occurs after SSO is performed.

Workaround:

 There is no workaround. 

•

CSCui32127

Symptom:

 CFM download error-objects are observed when CFM peers are reloaded or IM OIR is 

done on a scaled VPLS and CFM setup.

Conditions

: This issue occurs on the router with 250 or more CFM MEP sessions and more than 

1250 Layer2 virtual circuit sessions.

Workaround:

 There is no workaround.

•

CSCui34041

Symptom:

 Traffic does not flow to one of the prefix on MPLS template.

Summary of Contents for ASR 903

























































































































































































































































































Reviews:

No comments