manualshive.com logo in svg

Cisco ASR 903, Release Notes, Page: 202 / 280

Share
Download
Cisco ASR 903 Release Notes Download Page 202

 

16

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-08

  Caveats in Cisco IOS XE 3.9S Releases

•

CSCug14420

Symptom:

 Traceback observed while performing OIR of IM.

Conditions:

 This issue occurs while performing OIR T1E1 IM 

Workaround:

 There is no workaround.

•

CSCug21352

Symptom:

 The convergence time is more than 2secs on the router.

Conditions:

 This issue occurs when convergence time is more than expected. It takes around 2.5 

seconds to converge from Active to backup path with 450 CEM interfaces.

Workaround:

 There is no workaround. 

•

CSCug70182

Symptom:

 ASR903 -IMA8S port stays up without inserting a fiber.

Conditions:

 This issue is observed when GLC-FE-100FX optic is used

Workaround:

 There is no workaround.

•

CSCug77786

Symptom:

 The router develops false notifications, syslog messages and cefcFRUInserted traps 

when performing RP card switchover. The false notifications create false alarms in Prime Network.

Conditions:

 This issue occurs after RP card switchover on the router.

Workaround:

 There is no workaround. 

•

CSCug81561

Symptom: Convergence time is more than 50ms with EoMPLS after SSO.

Conditions: This issue occurs when port channel and BDI configurations exist on the router and SSO 
convergence time is more than 50ms.

Workaround: There is no workaround.

•

CSCug83807

Symptom: Multicast traffic is dropped as TCAM entries are encountered.

Conditions: This issue occurs when TCAM entries are encountered.

Workaround: There is no workaround.

•

CSCug91295

Symptom: UDP based ACLs do not work after a router reload.

Conditions: This issue occurs after reload.

Workaround: Remove and add the ACL. 

•

CSCug94257

Symptom: The 

show ptp port running detail

 command shows the wrong stream id. 

Conditions: This issue occurs under normal working conditions.

Workaround: Use the 

show plat soft ptp

 command get the correct stream id.

Summary of Contents for ASR 903

























































































































































































































































































Reviews:

No comments