manualshive.com logo in svg

Cisco ASR 903, Release Notes, Page: 243 / 280

Share
Download
Cisco ASR 903 Release Notes Download Page 243

C H A P T E R

 

1

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-08

6

Restrictions and Caveats in Cisco IOS XE 3.10 
Releases

This chapter provides information about restrictions and caveats in Cisco IOS XE 3.10 releases.

Note

We recommend that you view the field notices for the current release to determine whether your software 
or hardware platforms are affected. You can access field notices at 

http://www.cisco.com/en/US/support/tsd_products_field_notice_summary.html.

This chapter contains the following sections:

•

Limitations and Restrictions, page 6-1

•

Caveats in Cisco IOS XE 3.10S Releases, page 6-2

Limitations and Restrictions

The following limitations apply to the Cisco ASR 903 Router in IOS XE Release 3.10(0)S:

IPv6 Limitations

The following limitation applies when using IPv6 on the Cisco ASR 903 Router:

•

IPv6 Neighbor Discovery (ND) cache timer expiry is 4 hours. To prevent the neighbor adjacency 
from being deleted after the timer expires:

–

configure hardware based BFD sessions with the neighbors, or 

–

configure static IPv6 neighbors, or

–

configure the 

ipv6 nd cache expire timer refresh 

command.

Summary of Contents for ASR 903

























































































































































































































































































Reviews:

No comments