manualshive.com logo in svg

Cisco ASR 903, Release Notes, Page: 225 / 280

Share
Download
Cisco ASR 903 Release Notes Download Page 225

 

39

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-08

  Caveats in Cisco IOS XE 3.9S Releases

Conditions:

 This symptom is observed when you move an OC-3 interface module with an ATM 

configuration to a different bay and configure an ATM interface on the new bay. 

Workaround:

 There is no workaround. 

•

CSCuc42117

Symptoms:

 The router does not include 0xff03 flag leading bits within ppp fragment messages. 

Conditions:

 Occurs when the router has not negotiated ACFC. 

Workaround:

 There is no workaround. Most remote devices should ignore this behavior by design, 

but some devices may display unexpected behavior, such as for IPCP PROTREJ messages. 

•

CSCuc43719

Symptoms:

 ASR903 with dual RSP may crash.

Conditions:

 No specific trigger, but any configuration related to NBAR can make the box hit this 

issue.

Workaround:

 Do not have any NBAR configurations on the box as these are not supported on 

ASR903. 

•

CSCuc57130

Symptom:

 The router does not apply OC-3 interface module (IM) configurations.

Conditions:

 Occurs after an RSP switchover.

Workaround:

 There is no workaround. 

•

CSCuc59386

Symptoms:

 Continuous iomd crash on oc3im. Interfaces on oc3im not configurable, error message 

seen :- stand-by dosen’t support this command

Conditions:

 Seen on a HA ASR903 setup with oc3im. Seen when a iomd crash happens on active 

rsp and then standby iomd session handle is not cleared.

Workaround:

 Reload the stand-by rsp. 

•

CSCuc60148

Symptoms:

 System is not shutting down upon temperature sensor reaching ’SHUTDOWN’ 

threshold region. 

Conditions:

 Temperature sensors reached shutdown threshold region 

Workaround:

 IOS config command has to be explicitly configured to enable this system shutdown 

behavior. ’facility-alarm critical exceed-action shutdown’ 

•

CSCuc62784

Symptoms:

 Traces @ niles_if_count_initialize some times

Conditions: 

On performing Reload, Standby Reload, SSO

Workaround: 

No workaround. And these traces are displayed on the console and does not have any 

functionality impact to the system. 

•

CSCuc64509

Symptom:

 ASR903 as PTP master transmits clock class corresponding to holdover state on fresh 

bootup.

Conditions:

 ASR903 is not connected to any external frequency and Phase source and is using 

freerun internal clock to provide synchronization.

Workaround:

 ASR903 PTP master should be locked to external frequency and phase source.

Summary of Contents for ASR 903

























































































































































































































































































Reviews:

No comments