manualshive.com logo in svg

Cisco ASR 903, Release Notes, Page: 18 / 280

Share
Download
Cisco ASR 903 Release Notes Download Page 18

 

4

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-08

Chapter

  New Software Features in Cisco IOS XE Release 3.6S

New Software Features in Cisco IOS XE Release 3.6S

The following are the new software features introduced in Cisco IOS XE Release 3.6S:

Note

Many of the features supported on the Cisco ASR 903 Router require a license for use. For more 
information about supported licenses, see 

Software Licensing Overview, page 1-2

.

•

Any Transport over MPLS (AToM)—ATM AAL5 over MPLS (AAL5oMPLS)—The AAL5 
Transport over MPLS feature provides an ATM permanent virtual circuit (PVC) transport service 
for transporting AAL5 PDUs across an IP/MPLS backbone with rate-limit policing and configurable 
PVC priority value. A dynamic MPLS tunnel is configured to enable label imposition and 
disposition of encapsulated ATM PDUs transported between two edge routers having a Label 
Distribution Protocol (LDP) neighbor relationship.  For details about this feature, see:

–

http://www.cisco.com/en/US/docs/ios-xml/ios/mp_l2_vpns/configuration/15-2s/mp-any-transpo
rt.html

–

http://www.cisco.com/en/US/docs/ios/ios_xe/mpls/configuration/guide/mp_any_transport_xe.ht
ml

–

http://www.cisco.com/en/US/docs/ios/mpls/configuration/guide/mp_any_transport.html

–

http://www.cisco.com/en/US/docs/wireless/asr_900/software/guide/chassis/Release3.6.0S/ASR
903-Chassis-SW-36.html

•

BFD IPv6 Encapsulation—This feature introduces support for IPv6 addresses with the BFD 
protocol. For details about this feature, see 

http://www.cisco.com/en/US/docs/ios/ipv6/configuration/guide/ip6-bfd.html

•

BGP PIC Edge for IP/MPLS—This feature introduces support for BGP PIC Edge for IP/MPLS for 
sub-second convergence for IP and MPLS-VPN. For details about this feature, see:

–

http://www.cisco.com/en/US/partner/docs/ios-xml/ios/iproute_bgp/configuration/xe-3s/asr903/ir
g-xe-3s-asr903-book.html

–

http://www.cisco.com/en/US/docs/ios/iproute_bgp/configuration/guide/irg_bgp_mp_pic.html

–

http://www.cisco.com/en/US/docs/ios-xml/ios/iproute_bgp/configuration/15-2mt/irg-bgp-mp-pi
c.html

•

CFM over EFP interface with xconnect—This feature provides support for IEEE 802.1ag draft 
8.1-compliant CFM functionality on pseudowire & VFI interfaces. For details about this feature, 
see:

–

http://www.cisco.com/en/US/docs/wireless/asr_900/feature/guides/CFM_EFP_xconnect.html

–

http://www.cisco.com/en/US/docs/routers/7600/install_config/ES40_config_guide/es40_chap4.
html

•

CFM on Port-Channel Interfaces—This feature provides support for IEEE 802.1ag (CFM) on 
port-channel interfaces for end-to-end connectivity fault management on Ethernet networks. For 
details about this feature, see:

–

http://www.cisco.com/en/US/docs/ios/cether/configuration/guide/ce_cfm.html

–

http://www.cisco.com/en/US/docs/ios/ipsla/configuration/guide/sla_metro_ethernet.html

–

http://www.cisco.com/en/US/partner/docs/ios-xml/ios/cether/configuration/xe-3s/ce-cfm.html

Summary of Contents for ASR 903

























































































































































































































































































Reviews:

No comments