Chrysler 300 2017 Owner'S Manual Download Page 228 | Manualshive

Page: 228 / 488

background image

Turn Signal Indicator Lights

Green Telltale

Light

What It Means

Turn Signal Indicator Lights

The instrument cluster directional arrow will flash independently for the left or right turn signal
as selected, as well as the exterior turn signal lamp(s) (front and rear) as selected when the multi-
function lever is moved down (left) or up (right).

NOTE:

•

A continuous chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either
turn signal on.

•

Check for an inoperative outside light bulb if either indicator flashes at a rapid rate.

Speed Control SET Indicator Light

Green Telltale

Light

What It Means

Speed Control SET Indicator Light

This light will turn on when the electronic speed control is set to the desired speed. Refer to
“Speed Control” in “Understanding The Features Of Your Vehicle” for further information.

226

UNDERSTANDING YOUR INSTRUMENT PANEL

«
...
226
227
228
229
230
...
»

Summary of Contents for 300 2017









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 2017

Brand: Ranger design Pages: 6

21 COVERT Series

Brand: Code 3 Pages: 16

Brand: PEUGEOT Pages: 128

Brand: Schumacher Electric Pages: 87

2009 ESCALADE ESV

Brand: Cadillac Pages: 602

Brand: Phonocar Pages: 6

Brand: Yakima Pages: 11

Brand: JKS Pages: 3

Brand: GAC MOTOR Pages: 356

Brand: ULTIMATE SPEED Pages: 32

Brand: Chevrolet Pages: 441

Brand: Poison Spyder Pages: 5

Brand: BMW Pages: 64

Advanced Million Color

Brand: LedGlow Pages: 4

Brand: Ace K9 Pages: 14

Brand: Buick Pages: 475

Brand: Adaptiv Mini Pages: 4

Directechs FORD11

Brand: Directed Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands